User manual SANYO CCA-BC200

[. . . ] INSTRUCTION MANUAL CCA-BC200 Rear View Back up Camera System CAUTION · Installation and wiring require technical expertise and experience. To ensure proper installation and safety, consult the dealer where the product was purchased. SANYO'S HELP-LINE Call the toll-free number below if you have any difficulties operating this product. 1-800-421-5013 (Weekdays 7:30 AM ­ 5:00 PM, Pacific Time) 1- CONTENTS SAFETY PRECAUTIONS···································································································· 2 SPECIFICATION ················································································································· 4 BEFORE USING THE REAR VIEW BACK UP CAMERA SYSTEM···································· 5 ACCESSORIES AND HARDWARE ···················································································· 6 REAR VIEW BACK UP CAMERA SYSTEM OUTLINE ······················································· 7 CAUTIONS FOR CONNECTION ························································································ 8 CONNECTION ···················································································································· 9 BEFORE INSTALLATION ································································································· 10 INSTALLATION ················································································································· 12 CABLE ROUTING ············································································································· 15 GUIDE LINE ADJUSTMENT AFTER REAR VIEW CAMERA INSTALLATION················· 17 REAR VIEW CAMERA DISPLAY AND SWITCHING DISPLAY MODES·························· 23 SAFETY PRECAUTIONS <Safe and correct use of the product> · · · Before using the rear view back up camera, read this instruction manual for proper use of the product as directed. Sanyo and its suppliers are not responsible for damage or malfunction that arises from the failure to follow the instructions in this manual. [. . . ] Installing the camera in a position that obstructs vision is dangerous and could cause an accident. Install the camera so that it does not obstruct the rear view or vehicle operation, and make sure it does not protrude beyond the sides of the vehicle. To assure that the camera remains firmly attached to the vehicle: a) Do not install the rear view back up camera system outdoors in rainy or foggy weather. High humidity will prevent the camera from firmly adhering to the vehicle. b) If installation is required in areas of high humidity, completely dry the surface where the camera installation bracket is to be installed. c) If the temperature where the camera installation bracket is to be installed is low (68° or F lower), warm the location with a hair dryer so that the tape will adhere firmly to the surface. Do not apply heat to the camera or the lens. d) Do not install on a vehicle body or glass window with a surface that has been processed with a fluorine resin coating. The vehicle can be driven immediately after installation as long as the following DO NOT occur within a 24-hour period: a) Water is poured on the vehicle surface. c) Pulling or excessive force is applied to the camera. · · · · · Notes · Temporarily hook up the system, confirm that the system functions properly, and then install it permanently. · If the system does not function properly, re-check the connections. 10 Determination of Camera Installation Position (example) · · · · · Temporarily adhering the camera with the tape, locate a suitable installation position by adjusting the camera angle so that the rear of the vehicle (bumper and other areas) is visible in the monitor. Install the camera in a position that does not allow the illumination of a high-mount brake light to reflect into the camera lens. Make sure the camera does not contact or rub against the vehicle body when the rear door opens or closes. Removing and re-adhering the bracket will weaken the adhesion strength. Position the camera so that it is not aimed directly at the headlights of rear-oncoming vehicles. The recommended installation area is shown below: Installing the camera outside of this area could result in reduced camera functionality and reduced rear-view visibility. Recommended camera installation area Center of vehicle 70. 9 in 15. 7 in 15. 7 in 29. 5 in 9. 8 in 9. 8 in · Installing the camera on the rear spoiler or liftgate. (example) <Rear spoiler> <Liftgate> Need help?Call 1-800-421-5013 Camera Camera Note · The camera can also be installed in the taillight/license plate area or on the rear window. < Taillight/license plate area > Camera Camera < Rear window > 11 INSTALLATION Installing system on rear spoiler 1. Clean the location where the camera is to be installed. Wipe off oil, wax, moisture, dirt and dust using a cleaner and a clean cloth. 2. Peel off the paper backing from the tape on the camera bracket and firmly attach the bracket to a flat surface on the rear spoiler. Press the bracket with a finger to assure good contact of the bracket to the surface of the vehicle. Touching the sticky surface of the tape with a finger or re-adhering the bracket will weaken the adhesion strength and result in a loose installation that could eventually fall off. Bracket · If the temperature where the camera bracket is to be installed is low, warm the area with a hair dryer so that the tape adheres firmly to the surface. [. . . ] Each time the control switch is pressed, the 3 ft. guide line moves farther from the vehicle. Continuously pressing the control switch moves the line farther away until it exceeds a certain range and the line returns to the position closest to the vehicle. Set the 3 ft. Press and hold the control switch for more than two seconds. [. . . ]