User manual SANYO CLT670

[. . . ] 5 5 5 6 6 7 7 TABLE OF CONTENTS DIRECTORY . 17 Storing a name/number in the directory . Inserting a pause in the dialing sequence . Replacing a directory entry with a Caller ID entry Changing a stored name/number . [. . . ] Press MEM again to store the number. To view your directory, press MEM and use CID or to scroll. 16 17 CLT-2412E-NEW 7/16/02 9:09 AM Page 18 DIRECTORY Inserting a pause in the dialing sequence Press PAUSE twice to insert a delay in the dialing sequence of a stored telephone number when a pause is needed to wait for a dial tone (for example after you dial 9 for an outside line, or to wait for a computer access tone). Each pause counts as 1 digit in the dialing P sequence. P shows on screen. Note: Make sure to press PAUSE twice to enter a pause. If you press PAUSE once while entering a directory name/number, it will enter a # (number sign). DIRECTORY Replacing a directory entry with a Caller ID entry. Use CID or to select a specific Caller ID entry. SELECT MEMO 1 - 0 S E L E C T M E M O 1 - 0 shows on screen. Select the memory location you want to replace and press MEM. Press MEM again to confirm and save. 4. Reviewing and deleting directory contents 1. Make sure the phone is OFF (not in TALK mode). Use CID or to scroll through the directory until the desired name/number is shown, or use the number pad to select a memory location. M E M O # , the selected telephone number and name show on screen. Put the battery compartment cover back on. Place handset on the base to charge for 12 hours. Note: If the handset battery is removed for more than 5 minutes, the directory memory and Caller ID memory will be erased. Charge the handset battery for 12 continuous hours prior to first use. The initial battery charge is important for best performance. Caution: To reduce the risk of fire or personal injury, use a 3. 6 V, 600 mAh battery. Replacement part number: GES-3AHRAAAU. HEADSET JACK AND BELT CLIP Headset connection (Headset not included) For hands free conversation, connect the headset (not included) to the HEADSET jack. The handset earpiece and microphone are disabled when the headset is connected. · Press TALK to answer or place a call while using the headset. Belt clip installation · Attach the belt clip by inserting the sides of the belt clip into the slots. Snap the ends of the belt clip into place. · 20 21 CLT-2412E-NEW 7/16/02 9:09 AM Page 22 LCD SCREEN MESSAGES The following indicators show the status of a message or of the phone. ERROR ERROR Single Tone Two Long Beeps Caller information has been interrupted during transmission or the phone is excessively noisy. A long warbling tone SOUND SIGNALS Signals an incoming call A key is pressed Confirmation tone One short beep and one long beep Three short beeps 4 short beeps every 7 seconds Page signal ENTER NAME ENTER NAME Prompt telling you to enter name in directory. Error tone/Out-of-range warning Low battery warning DELETE ALL?DELETE ALL? Prompt asking you if you want to erase all Caller ID entries. TROUBLESHOOTING CALLER ID DELETE? Prompt asking you if you want to erase the current Caller ID entry or a directory entry that is shown on the screen. END OF LIST END OF LIST Indicates that there is no additional information in Caller ID list. NEW Indicates call or calls have not been reviewed. UNKNOWN NUMBER/UNKNOWN NAME/UNKNOWN CALLER UNKNOWN NUMBER/UNKNOWN NAME/UNKNOWN CALLER The incoming call is from an area not serviced by Caller ID, or the information was not sent. PAGING Someone has pressed the PAGE key on the base. No Display · Is battery fully charged? [. . . ] Accessory items including antenna, and batteries, Damage in or due to transportation. Damage due to improper maintenance, accident, abuse, misuse or negligence. Damage caused by lightning and power surges. LIMITATIONS a. reserves the right to change or improve the design of the model of the product warranted hereunder without incurring any obligation to make any modifications to or to install any improvement in or on the product. [. . . ]