User manual SANYO DC-MX42I

[. . . ] Switch off the unit when you don't use it. Switch off the unit and disconnect it from the AC power supply when it is not being used for a long time. (Plug, as the disconnected device entirely with power source, should keep in easy-tooperation in daily life. ) Don't install the unit in a place exposed to heating sources or direct sunshine. Don't install the unit in a place exposed to moisture or rain. [. . . ] We recommend using the Dolby Pro Logic Movie mode in lie of this 4-channel surround format. AUTO: Automatically selects processing mode based on the input format. 2. 6. 1. 3 PANORAMA This item is used to turn on/off panorama mode and is available only when MODE is set to MUSIC. When panorama mode is turned on, the front stereo audio is partially fed into the surround channels for an enveloping effect. 2. 6. 1. 4 DIMENSION This item is available only when MODE is set to MUSIC. This item allows gradual adjustment of the soundfield either towards the front or towards the rear. This is useful in setting a more even balance from all speakers with some rooms. 2. 6. 1. 5 CENTER WIDTH This item is available only when MODE is set to MUSIC. This item can be used to control the width of the center channel sound effect by blending the center speaker to the left and right speakers. As the level number increases, the center channel sound moves toward the left and right speakers. 2. 6. 2 REVERB MODE You can select a reverb mode in this item. -14- System Setup 2. 7 HDCD(High Definition Compatible Digital) HDCD (High Definition Compatible digital) is a patented encode/decode process for delivering the full richness and details of the sound from HDCD-encoded CDs. 2. 7. 1 FILTER You can set the digital filter to 2x, 1x or off. 2. 8 KARAOKE SETUP 2. 8. 1 MIC SETUP 2. 8. 1. 1 MIC Set this item to ON/OFF to switch on/off the connected microphone(s). 2. 8. 1. 2 MIC VOL Enter this item, then use direction key [ ]/[ ] to adjust the microphone volume. Then press [ENTER] to confirm your adjustment. 2. 8. 1. 3 ECHO LEVEL Enter this item, then use direction key [ ]/[ ] to adjust the microphone echo level. Then press [ENTER] to confirm your adjustment. 3 VIDEO SETUP PAGE 3. 1 VIDEO OUTPUT OFF: Set video output to the composite. YUV: Set video output in analog component video format if the component video outputs are used. P_YUV: Set video output as progressive YUV signals if the component video outputs are used. Press to open /close the disc tray. FUNCTION 1 4 7 2 5 8 0/10 3 6 9 10+ The digit keys can be used to input numbers or make selection of a track or a chapter, etc. Press to enter an item in the menu or to confirm and execute a selection. The direction keys can be used to move the highlight in the menu. ENTER SETUP Press to enter/exit the setup menu. GOTO This button is used to locate a position on a disc that you want a playback to begin from. Press this button, then use the direction keys and digit keys to set a specific track, disc time, track time, chapter, title, chapter time or title time of a disc to go to directly. Press this button to enter/exit the program menu with which you can playback the contents of a disc in your desired order. In the program menu, use the direction keys and digit keys to make a program list, then move the highlight to START and press [ENTER] to start program playback. During program playback, press [PROG] to enter the program menu. Press [ENTER] to cancel the current program playback. Or, press to return to the normal playback from the fast forward, fast reverse playback, etc. Press once to pause a playback, then press [ ] to continue the playback; Press it twice to stop a playback and the disc will be reset to the starting point. Press to return to the previous chapter/track. [. . . ] NOTE: In tuner mode, [VOLUME+/-], [CH-LEVEL], [MUTE], [TONE] and [S. EFFECT] buttons are available. For details, please refer to the remote control introduction in this chapter. For better FM reception, change the position of FM antenna wire. For better AM reception, adjust the position of AM external aerial loop . -22- Troubleshooting Before resorting to maintenance service, please kindly check by yourself with the following chart. Symptom Cause(s) Remedy No Power The AC power cord is not connected to the power supply or is not connected to a power supply securely. Please check that the AC power cord is connected securely. Video input mode of the connected Picture There is no TV isn't correctly set. [. . . ]