User manual SANYO DMP-P8

[. . . ] Table of Contents IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 PREPARATION FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 LOCATION OF CONTROLS AND INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 REMOTE CONTROL BATTERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Slide out the battery holder from the remote control case. (Push tab "A" towards the middle first, see diagram). Place one 3V CR2025 battery into the battery holder, observing the positive (+) direction. If the battery is placed incorrectly the remote control will not work. CAUTION: Danger of explosion if the battery is replaced incorrectly. Replace only with the same or equivalent type. Insert the battery holder into the battery compartment. Note: Please remove all of the batteries to prevent damage or injury from possible battery leakage if the unit is not to be used for a long period of time. . Use only the specified size and type of battery. -8- Operating Instructions Make sure the AC power cord from this unit is properly connected to a 240V 50Hz household AC power outlet. Make sure the AC power cord from this unit is properly connected to a 240V 50Hz household AC power outlet. ) Setting the Clock 1) While the unit is at STANDBY mode, press and hold MODE button on the top panel or the remote control for 2 sec. "12H" will show and flash on the display indicating that the clock is set to 12 hour format. 2) Press TUNE/SKIP button on the top panel or remote control once to change the clock format to 24 hour time. The display will change from "12H" to "24H" . 3) Press the MODE button to confirm. Press TUNE/SKIP button on the top panel or remote control to set the hour. 4) While hour is confirmed, minute digit will begin flashing. Press TUNE/SKIP button on the top panel or remote control to set the minute. Press MODE button to confirm. -9- Operating Instructions ) SETTING 1 or 2 ALARMS You can only set your Alarm mode at Standby mode. A. Set Alarm 1 1) While the unit is at STANDBY mode, press and hold ALARM 1 button on the top panel for 2 sec. Press "ALARM 1" button to confirm. 2) Minute digit will begin flashing, press "TUNE/SKIP" button to set the minute. Press "ALARM 1" button to confirm. 3) Wake up mode display will begin flashing, press TUNE/SKIP to select the below: a: Wake up to Radio : "FM Broadcasting"You have to pre ­ tune your desired radio channel in FM radio mode before setting the wake up function. b: Wake up to Radio: "AM Broadcasting You have to pre ­ tune your desired radio channel in AM radio mode before setting the wake up function. [. . . ] 3) Adjust the VOLUME level controls of this system as desired. V) Display Brightness Control During POWER ON Mode, Press SNOOZE button on top panel or remote control once to select Dimmer or Brightness display and the SANYO Logo. This will interchange between Dimmer and Brightness mode. - 14 - Operating Instructions During Stand By Mode, Press SNOOZE button on top panel or remote control once to activate the display from Dimmer (Default in Stand By mode) to Brightness mode for 9 sec. Then the display will return to Dimmer mode automatically. RESETTING If the system does not have any respond, you may have experienced a severe electric shock (ESD) or a power surge that triggered the internal computer to shut down automatically. If this occurs, simply disconnect the main power and connect the main power again after one minute. Note: Although disconnect the power will unlock the internal computer after a power surge, it will also erase all of the settings. [. . . ]