User manual SANYO DP26640

[. . . ] Then press Channel UP key. Initial On-Screen Display Monitor Usage Note: If you did not connect an antenna in Quik Step 1, you must run Channel Search twice. See Quik Step 3 below to connect a DVD player or similar Audio Video (AV) device. After the second channel search is complete, then you can use the INPUT key to select the Video 1, Video 2, Video 3, or HDMI inputs. INPUT key 2 POWER key CHANNEL UP key Press the CH L (channel up) key to start All Channel Search. No input signal sources could be located. [. . . ] After the second channel search is complete, then you can use the INPUT key to select the Video 1, Video 2, Video 3, or HDMI inputs. INPUT key 2 POWER key CHANNEL UP key Press the CH L (channel up) key to start All Channel Search. No input signal sources could be located. Please check cable or antenna connections. Then press Channel UP key. INPUT POWER Antenna 1 4 7 CAPTION 2 5 8 3 6 9 EXIT Antenna or Cable HDMI INPUT DIGITAL AUDIO OUTPUT DIGITAL ANTENNA IN UHF/VHF/CATV UHF/VHF/CATV CH PIX SHAPE AUDIO Part Number: 1JC6P1P0226A- 3 rd DVD PLAYER AND OTHER CRUCIAL DIGITAL EQUIPMENT AUDIO VIDEO CONNECTIONS DVD PLAYER CONNECTION (most common method) THE SIGNAL MAKES THE DIFFERENCE BEFORE YOU MAKE ANY AV CONNECTIONS. . . THE SIGNAL MAKES THE DIFFERENCE Don't be fooled by the phrase "Available in High-Definition. " To watch Satellite or Digital Cable HD programs in High-Definition, you must: 1. Subscribe to Satellite or Digital Cable High-Definition service. Connect your Satellite or Cable HD Receiver to the Component or HDMI input jacks on the DTV. Crucial Advice for Best Picture Composite and RF output signals from set-top boxes are Analog. These jacks are for compatibility to older analog equipment, such as, a VCR. DO NOT connect your HD Satellite receiver, HD Cable Box receiver, or DVD player to the Composite input jacks (VIDEO1) on the DTV. COMPONENT VIDEO OUT PR PB Y VIDEO OUT SELECT S OPT. The Component jacks on this DTV will accept HDTV, EDTV, or SDTV video signals, making Component a great choice when connecting your DVD player. For best viewing, avoid locating the DTV where direct sunlight or indoor lighting falls on the screen. When placing the unit in an enclosed cabinet, allow 3 to 4 inches spacing at the top, sides, and back, for proper ventilation. CONTROL PANEL POWER key VOLUME ­ + keys Simulated TV Image POWER VOL NOTE: The optimum viewing distance for your new Sanyo Wide Screen LCD DTV: Model DP26640. 6. 67 feet 1 2 Remove four (4) screws as shown. Carefully remove the DTV stand and store for possible later use. Back *LCD Mounting Screw Specifications: Model DP26640--M4 diameter, 10mm to 20mm in length Model DP32746--M6 diameter, 10mm to 20mm in length Threaded Inserts POWER VOL CH CH CHANNEL LM keys 6 th IDENTIFYING PICTURE SHAPES AND PIX SHAPE KEY OPERATION PIX MODES AND PIX SHAPE KEY OPERATION Pix Shape Key--Use the PIX SHAPE key on the remote control to change the display. Available options depend on the input signal and the aspect ratio of the broadcast. Picture Shape options are: Pix1, Pix2, Pix3, and Pix4. Pix2--A 16:9 image fills the screen normally. A 4:3 image is stretched horizontally and may appear distorted. [. . . ] Pix2--A 16:9 image fills the screen normally. A 4:3 image is stretched horizontally and may appear distorted. Pix3--This mode enlarges a Pix2 image vertically (some of the image may be cropped off). Pix3 image, with portions of the image cropped IDENTIFYING PICTURE SHAPES Pillarbox--Gray Bars are attached to the sides of the picture when a 4:3 aspect ratio program is displayed on your Wide Screen (16:9) DTV (Pix1). 4:3 image on a 16:9 screen without distortion NOTES: Your new Wide Screen television has a screen size aspect ratio of 16:9 (16 units wide by 9 units high), however, movies are often filmed at 2:1 or greater. [. . . ]