User manual SANYO DP46840

[. . . ] Press EXIT key to cancel setup. Initial On-Screen Display Skip Channel Search Option If you receive your local channels from a Satellite or Cable Box connection, or you intend only to watch videos or to play video games on this DTV, press the EXIT key to skip the Channel Search process. Then press the INPUT key on the remote control to select the AV signal source: Video 1, Video 2, Video 3, or HDMI. See Quik Step 3 below. INPUT key 2 POWER key EXIT key Press the CH L (channel up) key to start All Channel Search. INPUT POWER 1 4 7 CAPTION 2 5 8 3 6 9 EXIT No input signal sources could be located. [. . . ] Please check cable or antenna connections. Then press the Channel UP key. Antenna Antenna or Cable UHF/VHF/CATV DIGITAL ANTENNA IN SERVICE UHF/VHF/CATV CH PIX SHAPE AUDIO Part Number: 1JC6P1P0230-- 3 rd DVD PLAYER AND OTHER CRUCIAL DIGITAL EQUIPMENT AUDIO VIDEO CONNECTIONS DVD PLAYER CONNECTION (most common method) THE SIGNAL MAKES THE DIFFERENCE BEFORE YOU MAKE ANY AV CONNECTIONS. . . THE SIGNAL MAKES THE DIFFERENCE Don't be fooled by the phrase "Available in High-Definition. " To watch Satellite or Digital Cable HD programs in High-Definition, you must: 1. Subscribe to Satellite or Digital Cable High-Definition service. Connect your Satellite or Cable HD Receiver to the Component or HDMI input jacks on the DTV. Crucial Advice for Best Picture Composite and RF output signals from set-top boxes are Analog. These jacks are for compatibility to older analog equipment, such as, a VCR. DO NOT connect your HD Satellite receiver, HD Cable Box receiver, or DVD player to the Composite input jacks (VIDEO 1) on the DTV. COMPONENT VIDEO OUT PR PB Y VIDEO OUT SELECT S OPT. The Component jacks on this DTV will accept HDTV, EDTV, or SDTV video signals, making Component a great choice when connecting your DVD player. (See Skip Channel Search Option under Quik Step 2. ) S-Video VHF/UHF TO TV OUT 3 S-VIDEO OUT 4 DTV Back VIDEO1 VIDEO2 VIDEO3 Audio Video SERVICE S-VIDEO Y Pb Y Pb Pr L R INPUT POWER INPUT key 3 6 AUDIO OUTPUT Pr L R L R L R 1 4 2 5 5 th POSITIONING THE PLASMA DTV REMOVING THE FEET REMOVING THE FEET Tools Needed: Phillips screwdriver POSITIONING PRECAUTIONS Always use an appropriate table or stand when positioning your Plasma DTV. For best viewing, avoid locating the DTV where direct sunlight or indoor lighting falls on the screen. NOTE: The optimum viewing distance of your new Sanyo Wide Screen Plasma DTV is 8. 75 feet. Allow adequate space for proper ventilation (3 to 4 inches on the sides, top, and back). Simulated TV Image 1 Remove two (2) screws from each foot bracket, then slide the feet out of the brackets. IMPORTANT NOTE: Place the DTV face down on a padded or cushioned surface to protect the screen and finish. 6 th IDENTIFYING PICTURE SHAPES AND PIX SHAPE KEY OPERATION PIX MODES AND PIX SHAPE KEY OPERATION Pix Shape Key--Use the PIX SHAPE key on the remote control to change the display. Available options depend on the input signal and the aspect ratio of the broadcast. Picture Shape options are: Pix1, Pix2, Pix3, and Pix4. Pix2--A 16:9 image fills the screen normally. A 4:3 image is stretched horizontally and may appear distorted. [. . . ] Pix2--A 16:9 image fills the screen normally. A 4:3 image is stretched horizontally and may appear distorted. Pix3--This mode enlarges a Pix2 image vertically (some of the image may be cropped off). Pix3 image, with portions of the image cropped IDENTIFYING PICTURE SHAPES Pillarbox--Gray Bars are attached to the sides of the picture when a 4:3 aspect ratio program is displayed on your Wide Screen (16:9) DTV (Pix1). 4:3 image on a 16:9 screen without distortion NOTES: Your new Wide Screen television has a screen size aspect ratio of 16:9 (16 units wide by 9 units high), however, movies are often filmed at 2:1 or greater. [. . . ]