User manual SANYO DP50719

[. . . ] Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK); NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] · Do not place the VCR directly on top of the TV. This may cause interference in the picture and sound (of the VCR) during the recording or playback mode. If this interference occurs, locate the VCR away from the TV. 18 VIDEO CASSETTE TAPES SAFETY TAB This VCR will operate with any video cassette which has the mark. The table below shows the recording/playback time of VHS cassettes when they are used in the SP, LP and SLP speeds. (LP speed is for playback only. ) TYPE SPEED To prevent accidental erasure, remove the tab after recording. 480 mins. PREPARATION WHEN HANDLING VIDEO CASSETTES To record again cover the hole with vinyl tape. · Do not expose video cassettes to extreme heat, high humidity, or strong magnetic fields. · Do not tamper with the cassette mechanism. · Do not touch the tape with your fingers. · Always store an unused cassette in its case. LOADING Hold the cassette with the arrow side up (top). Insert the cassette gently into the slot in the direction of the arrow (on the cassette) until the loading mechanism automatically pulls the cassette into the unit. 7 Turn off the VCR and the auto clock setting works. 20 SETTING THE CLOCK (Cont'd) MAIN MENU CLOCK PROGRAM TUNING SETUP SELECT ENTER TO EXIT PRESS MANUAL CLOCK SET Example: July 5, 2001 ; 2:15 AM 1 Press MENU and the MAIN menu will appear. 2 Press D or E to choose the CLOCK menu. Press ENTER and the CLOCK menu will appear. CLOCK SET MENU MONTH : JANUARY DAY : 1 MON YEAR : 2001 TIME : 12 : 00 AM AUTO CLOCK SET : ON DAYLIGHT SAVING: AUTO TIME ZONE: AUTO 3 Press F or G to choose the month. 4 Press E to choose the DAY item. Press F or G to choose the day. The day of the week will display automatically. PREPARATION SELECT ADJUST TO EXIT PRESS MONTH : JULY DAY : 5 THU YEAR : 2001 TIME : 12 : 00 AM AUTO CLOCK SET : OFF DAYLIGHT SAVING: AUTO TIME ZONE: AUTO 5 Press E to choose the YEAR item. Press F or G to choose the year. SELECT ADJUST TO EXIT PRESS 6 Press E to choose the TIME item. Press F or G to choose the time. MONTH : JULY DAY : 5 THU YEAR : 2001 TIME : 12 : 00 AM AUTO CLOCK SET : OFF DAYLIGHT SAVING: AUTO TIME ZONE: AUTO 7 Press E to choose the DAYLIGHT SAVING item. Press or G to choose the ON or OFF. F SELECT ADJUST TO EXIT PRESS 8 Press MENU when finished. MONTH : JULY DAY : 5 THU YEAR : 2001 TIME : 2 : 15 AM AUTO CLOCK SET : OFF DAYLIGHT SAVING: AUTO TIME ZONE: AUTO NOTE SELECT ADJUST TO EXIT PRESS The "AUTO CLOCK SET" must set to "OFF". If set to "ON", an incorrect date and/or time will be entered again when the VCR is turned off. MONTH : JULY DAY : 5 THU YEAR : 2001 TIME : 2 : 15 AM AUTO CLOCK SET : OFF DAYLIGHT SAVING: ON TIME ZONE: AUTO SELECT ADJUST TO EXIT PRESS 21 NORMAL PLAYBACK PREPARATION · Turn on the TV. · Be sure the TV is set to the VCR Output Channel (CH 3 or 4). · If a direct VIDEO/AUDIO connection is made between the VCR and the TV, set the TV's source selector to VIDEO. NORMAL PLAYBACK 1 Insert a prerecorded video cassette. The TAPE IN indicator will light and the VCR will power-up automatically. · Make sure that the TIMER indicator in the VCR indicator panel is not lighted. · If a tape without a safety tab is inserted the unit will start the playback automatically. POWER 1 4 7 SLOW EJECT 2 5 8 0 3 TV/VCR 6 Ad JUMP 9 INPUT SP/SLP REC 2 Press PLAY once. The PLAY appears on the TV screen . · It is not necessary to select the tape speed for playback. [. . . ] · Check if POWER indicator is lit on the VCR indicator panel. If not, make sure power cord is plugged in. · If the TAPE IN indicator flashes, press POWER again. · Press TV/VCR to select the VCR mode. [. . . ]