User manual SANYO DS13390

[. . . ] This product is only used for Monitors that have a terminal for the PJ-Net Organizer. This manual explains the installation of the PJ-Net Organizer and its operation. INSTALLATION and OPERATION of the PJNet Organizer OWNERS MANUAL Preparation Compliance Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 SANYO DS13390 of the FCC Rules. These limits are designed to provide Tested To Comply reasonable protection against harmful interference in a With FCC Standards residential installation. This equipment generates, uses FOR HOME OR OFFICE USE and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] When you set up the network of monitor which has a default setting by using the computer, it must be carried out in the network which does not provide any gateways (routers). 15 Installation The Flash Player version 9 or later is required when you control the monitor. If your computer does not have, follow to the message on the control page to install the Flash Player. For further product information or installing, see the homepage. (http://www. adobe. com) Flash Player 16 Installation Configure the network of computer Configure the network of computer When you use the monitor through the network, the IP address of the monitor must have the same IP network number of the existing network. Also it is required to use the same IP network number of the computer to set up the monitor. In the network included with the gateway (router), it must be used with the IP network number specified by the gateway (router). Configure the computer's network by following steps: Windows 2000 This example explains how to set the following network address. IP Address : 192. 168. 0. 5 Subnet Mask : 255. 255. 255. 0 Gateway Address : 192. 168. 0. 1 1 Select 2 3 4 5 the Network and Dial-up Connections menu from [Start] - [Settings] menu. Click the Local Area Connection icon with right button of the mouse and then select the Properties menu from the popup menu. The right window will appear on the screen. Select the Internet Protocol(TCP/IP) *1 on the General tab of the "Local Area Connection Properties" dialog window and then press the Properties button. On the "Internet Protocol (TCP/IP) Properties" dialog window, select the Use the following IP address button and then enter the IP Address*2 and Subnet mask. In this case type "user" onto the User Name text area and the login password onto the Password text area and then click OK button. If you check the item "Remember my password", you can login without entering the password for the next login. * The entering User Name must be "user" and it cannot be changed. [Note] When accessing the monitor at first time or setting the no password [0000], the autologin will be performed and the next main setting page is displayed. Important If you have forgotton current network configuration(IP address, subnet mask, password DNS, and default gateway, you can set them to default value via serial port (RS232C) Refer to page 42 22 Login the setting page of the monitor 3 Display of setting page The following setting page of the monitor is displayed. Perform the various kinds of setting through this page. Press a button of Main Menu to display the control or setting page. The main menu which can be set up and control the monitor appears on the lower side of the page. On the setting page, the control and status items for selected menu are displayed. The "Status" page is displayed as the default. This page indicates the current status of the monitor. For further information, please see chapter "Controlling the monitor" on page 31. Sub Menu Setting Page Main menu 23 Basic Setting and Operation Initial Settings After installing this product onto the monitor, perform the following basic initial setting. Press the Initial Setting button on the main menu to display the initial setting page. [. . . ] Press the Save button to memorize. The maximum 127 characters can be typed. Use other command This function can be used to send other command which does not have in the menu of this board. Press the Other button on the main menu. The following setting page will be displayed. Type the command and press the Send button to control the monitor. Please see the chapter "4: Serial Port Use" on page 39 or the owner's manual of the monitor for other command. [. . . ]