User manual SANYO DS19500

[. . . ] G Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation. 2 To the Owner Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. [. . . ] Select the Video System Selection menu with the POINT UP/DOWN button, and then press the POINT RIGHT button to enter the sub-menu. Video System Selection menu (Y-Pb/Cb-Pr/Cr) 2 Choose the system that you want to select with the POINT UP/DOWN button, and then press the SELECT button to activate the item. Auto The projector automatically detects incoming video system, and adjusts itself to optimize its performance. COMPONENT VIDEO SIGNAL FORMAT If the projector cannot reproduce proper video image, select a specific component video system among 480i, 575i, 480p, 575p, 720p, 1035i, and 1080i. 26 Video Input Image Level Selection (Direct Operation) Select the image level among Standard, Cinema, Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. (See the next section "Image Level Selection (Menu Operation)" about each item. ) IMAGE button Standard Cinema Image 1 IMAGE button INPUT IMAGE VIDEO IMAGE NO SHOW Image 2 Image 3 AUTO 1 VIDEO KEYSTONE 2 S-VIDEO 3 Image 4 COMPONENT COMPO 4 IMAGE 1-4 button Image Level Selection (Menu Operation) 1 Press the MENU button, and the main menu appears. Select the Image Level Selection menu with the POINT UP/DOWN button, and then press the POINT RIGHT button to enter the sub-menu. Image Level Selection menu Image Level Selection menu 2 Choose the level that you want to set with the POINT UP/DOWN button, and then press the SELECT button to activate it. Standard The level being selected. Normal picture adjustment preset on this projector. Cinema Picture level adjusted for the picture with fine tone. IMAGE 1~4 User preset picture adjustment in Image Level Adjustment menu (p28, 29). Close the Image Level Selection menu. 27 Video Input Image Level Adjustment 1 Press the MENU button, and the main menu appears. Select the Image Level Adjustment menu with the POINT UP/DOWN button, and then press the POINT RIGHT button to enter the sub-menu. Image Level Adjustment menu Image Level Adjustment menu 2 Choose the item that you want to adjust with the POINT UP/DOWN button, and then press the POINT LEFT/RIGHT button to adjust each item. The items displayed in a line can be adjusted while you see the change of the image. Press the SELECT button to finish adjusting an item. The on-screen menu returns to the sub-menu. Press the SELECT button at this icon to display other items. Press the SELECT button at this icon to close the item. 3 To store the adjustment data, select the Store with the POINT UP/DOWN button and press the POINT RIGHT button. When your video equipment (such as DVD) has 16 : 9 output mode, select 16 : 9 and select the Full on this Screen Size Adjustment menu to provide better quality. Zoom Provides an image to fit screen size (16 : 9 aspect ratio) by expanding the image width and height uniformly. This function can be used for providing a letter box mode picture (4 : 3 aspect picture with black bar on the top and bottom edges) at wide video aspect of 16 : 9. Normal Provides an image at the normal video aspect ratio of 4 : 3. Full Close the Screen Size Adjustment menu. Zoom Normal 30 Computer Input / (RGB Scart 21-Pin Video Input) Input Source Selection (Direct Operation) WARNING TEMP. READY INPUT BUTTON LAMP REPLACE ON-OFF LAMP You can select Computer input or Video input with the INPUT button. (The input source that is selected last is selected when the projector is turned on. ) If the projector cannot reproduce proper image, select a correct input source through menu operation as shown below. INPUT button Computer Video RGB Scart Input TOP CONTROL When RGB Scart 21-pin output is available in video equipment, connect the Scart connector to the "COMPUTER IN" on the projector with an optionally supplied Scart-VGA cable. It can reproduce higher MENU INPUT resolution and quality of picture. (See page 51 for order. ) SELECT To select RGB Scart input, follow the procedures described below. Note RGB Scart input (COMPUTER IN) can receive 575i only. REMOTE CONTROL INPUT IMAGE VIDEO AUTO NO SHOW IMAGE 1 VIDEO 2 INPUT button Input Source Selection (Menu Operation) 1 Press the MENU button, and the main menu appears. Select the Input Source Selection menu with the POINT UP/DOWN button, and then press the POINT RIGHT button to enter the sub-menu. Input Source Selection menu Input Source Selection menu 2 Choose the Computer with the POINT UP/DOWN button and press the POINT RIGHT button. [. . . ] G Check the input source is selected properly. (Refer to page 21. ) G When turning the projector on, it takes about 30 seconds to display an image. G Check the system that you select is corresponding with video equipment or your computer. G Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C). [. . . ]