User manual SANYO DS27425

[. . . ] 2 Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Names of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Do not stick anything into the air outlet of the outdoor unit. This is dangerous because the fan is rotating at high speed. · Do not let children play with the air conditioner. · Do not cool or heat the room too much if babies or invalids are present. 2-3 Unit Display and Operation Controller for K, X, and T Types Remote control receiver OPERATION lamp TIMER lamp STANDBY lamp 2 NORM. OFF TEST Remote control receiver OPERATION lamp OPER. STDBY TIMER TIMER lamp STAND BY lamp OPERATION lamp TIMER lamp STANDBY lamp This lamp lights when the appliance is turned on. This lamp lights when the system is being controlled by the timer. When the unit is in the heating standby condition, the STANDBY lamp lights. If the unit is used for cooling only, the STANDBY lamp will not illuminate. This lamp operates only when an alarm occurs. This section picks up infrared signals from the wireless remote controller (transmitter). If the unit is used for cooling only, the STANDBY lamp will not illuminate. This lamp operates only when an alarm occurs. This lamp lights when the filter needs cleaning. H: OPERATION lamp I: TIMER lamp J: STANDBY lamp K: FILTER lamp Turning off the ON/OFF operation button does not disconnect the power. Use the main power switch to turn off the power completely. 2-6 Using the Wireless Remote Controller How to Install Batteries 1. Press and slide the cover on the back of the wireless remote controller in the direction of the arrow. Install two AAA alkaline batteries (LR03). Make sure the batteries point in the direction marked in the battery compartment. Press the ACL button, then replace the cover. If you press it, the current time, ON time, and OFF time are all reset to 0:00. ACL ACL button button Cover Cover · · · · The batteries last about six months, depending on how much you use the wireless remote controller. Replace the batteries when the wireless remote controllers lamp fails to light, or when the wireless remote controller cannot be used to change the air conditioners setting. Use two fresh leak-proof type-AAA alkaline batteries (LR03). [. . . ] J: This indication appears when the temperature is set. K: When turning on the power switch of the system controller, sign blinks for a few minutes. While blinking, any controls using the system controller are inhibited. This is because the system controller is verifying connected groups. 3-7 I How to start group operation To start group operation 4 2 Stop 1 3 5 9 6 7 8 Power 1 2 3 4 5 6 Turn the power supply switch on more than 5 hours before starting operation. [. . . ]