User manual SANYO DVD-S2000

[. . . ] Its performance is much better than that of any previous home video equipment. As the best signal source , it will give you the uppermost enjoyment! Built-in Dolby AC-3, MPEG, PCM etc. Hi-Fi, 96kHz/24bit audio digital processor. High-resolution component video output, support the future video equipment. [. . . ] They are analog audio output system and digital audio output system. Analog audio output system includes 2-channel stereo output and Dolby AC-3 5. 1 channel output. Digital audio output system includes coaxial output. Stereo Audio Use a pair of audio cable (white for left, red for right) to connect the stereo audio outputs of this unit to the stereo inputs of a TV or a power amplifier. 5. 1 CH Audio Use 3 pairs of audio cables to connect the 5. 1 CH audio outputs of this unit to the 5. 1 channel inputs of external audio amplifiers or other players. Coaxial Audio Use a coaxial cable to connect the coaxial output of this unit to the coaxial input of a power amplifier. TV/Monitor/Amplifier Audio Input L R 5. 1 CH Audio Input 2CH Audio Input Digital Audio Input COAXIAL FL SL SW FR SR 5. 1 CH AUDIO OUT CEN L R COAXIAL 5. 1 CH Audio Output 2CH Audio Output Digital Audio Output Note: DVD Audio Output The audio settings should conform to the actual audio system connections. Please refer to the Audio Setup in System Setup. AC POWER CONNECTION After checking all the connections have been made correctly, plug the AC power lead of this unit into the wall socket. NOTE: Unplug the AC power lead from the wall socket if the unit will not be in use for a prolonged period of time. -11- System Setup Menu Operation 1. Press [SETUP] on the remote control to show the setup menu. The submenu of the selected item will be displayed below instantly. Press [ ]/[ ] to select an item you desire to set in the submenu, then press [ENTER] / [ ]to enter. Use [ ]/[ ] to select an option, then press [ENTER] to confirm it, or press [ ] to cancel. Then you can press [ ]/[ ] to continue to set other items in the submenu. Press [ ] to go back to the superior menu of the current one. The delay is to compensate for the audio propagation time difference caused by the distance difference of the speakers to the listener. Use the direction key [ ]/[ ] to select a speaker, center speaker, subwoofer, left surround speaker or right surround speaker. Then use the direction key [ ]/[ ] to set the distance difference. NOTE: The unit does not support delays for when the distance between the center or surround speakers and the listener are longer than that between the front speakers and the listener. In case the channel delay settings cannot match your speaker configuration, please set all distance difference to 0cm. Sub woofer 0cm 2. 5 EQUALIZER 2. 5. 1 SOUND MODE Select a sound mode in this item. 2. 5. 2 BASS BOOST Set it to ON to boost the bass sound. 2. 5. 3 SUPER BASS Set it to ON to get the super bass sound effect. 2. 5. 4 TREBLE BOOST Set it to ON to boost the treble sound. -14- System Setup 2. 6 3D PROCESSING 3D processing provides a virtual surround sound experience using just two speakers. 2. 6. 1 PRO LOGIC II Pro Logic II: This unit allows you to configure Dolby Pro Logic II to expand 2-channel source audio into full 5. 1-channel surround sound. NOTE: Pro Logic II functionality is effective only when DOWNMIX is set to 5. 1CH and DIGITAL OUTPUT is set to SPDIF RAW. 2. 6. 1. 1 PRO LOGIC II This item is used to turn on or off the Pro Logic II processing. ON: Pro Logic II processing is always on. OFF: Pro Logic II processing is disabled AUTO: Pro Logic II processing is on only when Dolby Pro Logic II encoded content is detected. NOTE: When the Pro Logic II processing is turned off, all the following items (MODE, PANORAMA, DIMENSION and CENTER WIDTH) are unavailable. 2. 6. 1. 2 MODE This item is used to set the processing mode of Pro Logic II. MUSIC: The surround experience is tailored for multi-channel music playback. MOVIE: Emphasis is given to the center channel as two-channel audio is decoded and played back into your 5. 1 system. [. . . ] [ ]/[ ]: Press to rotate the picture counterclockwise/ clockwise during the playback. [ ]/[ ]: Press to create a vertical/horizontal mirror image. KARAOKE PLAYBACK Set the item MIC to ON and set the MIC VOL to a low level in the karaoke setup menu. Insert a microphone into the microphone socket on the front panel. Adjust the microphone volume again if required and the echo to your desired level in the karaoke setup menu. [. . . ]