User manual SANYO EC232

[. . . ] This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for many years to come. Improper operation may result in not only shortening the product life, but also malfunctions, fire hazard, or other accidents. Safety Precaution ­ ­ ­ This apparatus must be earthed. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. [. . . ] When the projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons. Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition. 3 English Hot air is exhausted from the exhaust vent. When using or installing the projector, the following precautions should be taken. ­ Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes. ­ Keep the exhaust vent at least 3' (1 m) away from any objects. ­ Do not touch a peripheral part of the exhaust vent, especially screws and metallic part. This area will become hot while the projector is being used. ­ Do not put anything on the cabinet. Objects put on the cabinet will not only get damaged but also cause fire hazard by heat. Control Panel Remote Sensor Focus Ring Ventilation (outlet) Lens Lens Cap (with String) Ventilation (inlet) Speaker 6 Connection Ports 1 2 3 4 5 6 7 8 9 SERVICE PORT S-VIDEO IN VIDEO IN MONITOR OUT COMPUTER IN 1 COMPONENT IN 1 AUDIO IN (VARIABLE) AUDIO OUT COMPUTER IN 2 COMPONENT IN 2 10 SERVICE Port HDMI Port S-VIDEO IN Connector VIDEO IN Connector MONITOR OUT Connector 6. Speaker Control Panel 1 2 3 4 5 6 7 8 TEMP LED LAMP LED POWER LED INPUT Button ON/STAND-BY Button Four Directional Select Keys 7. 6. 7 English Remote Control 1 2 3 4 15 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 16 17 18 19 20 21 22 23 24 Infrared trans- Sends signals to the projector. mitter Infrared indica- Signals indicator for sending. tor ON/STAND-BY Refer to the "Power On/Off the Projector" section. ENTER Confirm your section of items in sub menu operation. MENU Press "MENU" to launch the Onscreen display (OSD), back to the top level of OSD for the OSD main menu operation IMAGE Select the Image mode from Presentation, Movie, sRGB, Bright and User. 8 7 N ot e To quick change remote control code, press "MENU" and "IMAGE" buttons about 10 seconds at the same time. 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 N ot e The bottom side of OSD menu might be out of display when user adjusts keystone value, under the status of low resolution signal input and different aspect ratio setting. To solve this problem, please adjust keystone value in "Aspect Ratio" of "4:3" then switch back to your desired aspect ratio. Press "INPUT" to choose RGB, SCART, Component, S-Video, Composite and HDMI sources. KEYSTONE +/- Adjust the image to compensate for distortion caused by tilting the projector. Point the remote Maximum operating range control from obliquely for the remote control is above toward the Inabout 39. 4' (12m) and 60° in frared Remote Receiver top of the projector. when operating the remote control. 39. 4' (12m) Approx. 30° 10 Connecting the Projector Connect to Computer/Notebook VGA, DVI N ot e Make sure that the power plug is fully inserted into both the projector AC inlet and the wall outlet. [. . . ] The OSD will be closed and the projector will automatically save the new settings. N ot e If no button operation is made for 30 seconds, the OSD will be closed automatically. Main Menu Sub Menu Setting 17 Replacing the lamp The projector will detect the lamp life itself. It will show you a warning message Warning: To avoid burns, allow the projector to cool for at least 45 minutes before you replace the lamp! When you see this message, change the lamp as soon as possible. Make sure the projector has been cooled down for at least 45 minutes before changing the lamp. 1 2 3 4 Lamp Replacing Procedure: Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. [. . . ]