User manual SANYO HT27546

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or other moisture. CAUTION: Changes or modifications not expressly approved by the manufacturer may void the user's authority to operate this equipment. For the customers in Canada This class B digital apparatus complies with Canadian ICES-003. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generated, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] (Please refer to page 27, "ALARM RECORDING". ) oe If the "REPEAT RECORD" setting is R 1, the REPEAT indicator will go off if there is an alarm trigger. After alarm recording, the recording will continue to the end of the tape then it will be rewound to the beginning and stop. "OFF" will be displayed on the digital display. To turn off the buzzer (if in the (BUZZER SET) menu, TAPE END is set to "Y") and the "OFF" display, press the STOP, EJECT, FF, REW or PLAY button. oe If "A" is displayed on the digital display and the "REPEAT RECORD" setting is R1, autorepeat recording is not possible. 1 Press the MENU button to display the (MAIN MENU 1) menu. 2 Press the SHIFT ] button to select the "6. RECORD SET" line, then press the MENU button. ø The (RECORD SET) menu appears. REW 3 Press the SHIFT ] (or \) button, until the "TAPE END MODE" (or "REPEAT RECORD") setting is flashing. 4 Press the DATA l (or j) button to set to "R 1" or "R 2". (Please refer to page 24, "Setting the Mode at the End of the Tape". ) 5 Press the MENU EXIT button to save the setting. ø The REPEAT indicator will light. 6 Press the REC/PLAY SPEED l (or j) button to set the recording speed mode. 7 Press the REC button. ø Recording will start. When the tape end is reached, the VCR will rewind it to the beginning, and recording will resume. ø When the end of the tape is reached, a buzzer will be heard (if in the (BUZZER SET) menu, TAPE END is set to "Y") and "OFF" will be displayed until the rewinding operation starts. 26 English ALARM RECORDING By connecting the ALARM IN terminal to a door switch, an interphone, etc. , a recording can be done only when necessary. 4 Press the DATA l (or j) button to select the desired recording speed, then press the SHIFT ] button. oe The maximum display number of alarm recordings is "999", at the next alarm recording the counter will indicate "000". oe When the (ALARM LOG) menu is displayed, press the MENU RESET button to reset the alarm counter to "000" (all the data of the (ALARM LOG) menu is reset). Checking the Alarm Recordings Time The date and time of up to 100 alarm recordings can be displayed. 1 Press the MENU button to display the (MAIN MENU 1) menu. 2 Press the SHIFT ] (or \) button until the (MAIN MENU 2) menu is displayed. <MAIN@MENU@2> 1. RS-485@SET 2. ALARM@LOG 3. POWER/DEW/USED@TIME 4. SECURITY@LOCK TO@MAIN@MENU@1 Connections to the ALARM IN/OUT Terminals oe Alarm input signal Connect a make-contact (no voltage) switch between the ALARM IN and COM terminals. oe Alarm output signal Normally DC 5V are output between the ALARM OUT and the COM terminals. When an alarm input (trigger) is received and the unit is recording, the output falls to 0V. Once the alarm recording is over, the output returns to DC 5V. 3 Press the SHIFT ] (or \) button to select the "2. ALARM LOG" line, then press the MENU button. ø The (ALARM LOG) menu appears. @010@08-25@10:30 ø The number of alarm recordings, and the 10 most recent alarm recording times are displayed. NOTE: ALARM RESET IN terminal oe If the circuit between the ALARM RESET IN terminal and COM terminals is closed during alarm recording, alarm recording mode is canceled. oe Continue pressing the SHIFT ] button to display the next 10 alarm recordings entries. When the number of alarm recording entries reaches 100, the older ones are erased as new ones are memorized. 4 Press the MENU EXIT button, the normal screen is displayed. NOTE: oe If the MENU RESET button is pressed while the (ALARM LOG) menu is displayed, the displayed data is erased. "A" will be erased from the digital display. 28 English ALARM RECORDING Alarm Search To go to the beginning of a desired alarm recording. Alarm Scan To look for an alarm recording by viewing the first 5 seconds of each alarm recording. 1 Press the SEARCH button during stop mode. ø "AL SEARCH 01" will be displayed on screen. 1 Press the SEARCH button twice during stop mode. ø "AL SCAN" will be displayed on screen. 2 Press the DATA l (or j) button to set the desired alarm number (1 to 99), then press the FF (or REW) button. ø Playback will start just before the desired alarm recording, then switch to a still image at the beginning of the desired alarm recording. 2 Press the FF (or REW) button. ø The unit will advance (or rewind) the tape at high speed and playback the first 5 seconds of every alarm recording. NOTES: oe The playback of a block which includes the alarm recording will start. [. . . ] After this, repeat from the start or the table. For places with symbols such as E (k) and F (k), carry out checking and cleaning, and replace if necessary. This periodic maintenance check table changes considerably according to the using conditions and environment. Refer to (POWER/DEW/USED TIME) menu for the length of time the unit has been used. [. . . ]