User manual SANYO PDP-32H1A

[. . . ] If your Plasma Monitor seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the Plasma Monitor or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This Plasma Monitor should be set in the way indicated. Take appropriate space on the top, sides and rear of the Plasma Monitor cabinet for allowing air circulation and cooling the Plasma Monitor. If the Plasma Monitor is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. [. . . ] Zoom (Caption-IN) Provides an image including a caption to fit the screen size (16 : 9 aspect ratio) by expanding the width and height of the image uniformly. SURROUND AUTO PC POWER FREEZE! FREEZE! Full Provides an image to fit width of screen by expanding image width uniformly. This function can be used for enjoying a squeezed video signal with wide video aspect ratio of 16 : 9 screen. When your video equipment (such as DVD) has 16 : 9 output mode, select 16 : 9 and select Full to provide better quality. Normal Provides an image at a normal video aspect ratio of 4 : 3. 20 BASIC OPERATION SELECTING INPUT SOURCE VIDEO INPUT Select either "AV1" or "AV2" or "AV3" by pressing the VIDEO button on the Remote Control Unit. (Refer to "CONNECTING TO VIDEO EQUIPMENT" on Page 13. ) AV 1 AV 2 AV 3 COMPONENT INPUT Select "Component1" or "Component2" by pressing the COMPONENT button on the Remote Control Unit. (Refer to "CONNECTING TO COMPONENT VIDEO EQUIPMENT" on Page 14. ) Component 1 Component 2 PC/DVI-D INPUT Select "PC" or "DVI-D" by pressing the PC/DVI-D button on the Remote Control Unit. (Refer to "CONNECTING TO COMPUTER" on Page 15. ) PC DVI (PC) VIDEO button NOTE : By pressing the STATUS button on the Remote Control Unit, the selected input source, ECO mode indication (if the Eco mode is set) and OFF TIMER's remaining time (if the OFF TIMER is set) will be displayed for 5 seconds. INPUT VIDEO COMPONENT ON-OFF PC/DVI-D PC/D COMPONENT button VOLUME OLUME OFF TIMER MUTE WIDE PICTURE MOVE UP PC/DVI-D button FRONT CONTROL OPERATION Choose either input mode by pressing INPUT button on the Plasma Monitor's Front Control. STATUS MOVE DOWN MENU SURROUND AUTO PC POWER AV 1 AV 2 AV 3 4 Component 1 MENU OK INPUT ­ VOLUME + Component 2 INPUT button PC DVI (PC) 21 BASIC OPERATION PICTURE IMAGE LEVEL SELECT VIDEO/COMPONENT MODE Select an image level among Dynamic, Natural, Cinema and Memory by pressing the PICTURE button on the Remote Control Unit. Dynamic High contrast picture level preset on this Plasma Monitor. Natural Normal picture level preset on this Plasma Monitor. Cinema Picture level adjusted for the picture with fine tone. Memory User preset picture adjustment in the IMAGE ADJUST Menu (P26). Dynamic Natural Cinema Memory In Video / Component mode VIDEO COMPONENT ON-OFF PC/DVI-D PC/D VOLUME OLUME OFF TIMER MUTE WIDE PICTURE MOVE UP PICTURE button OK STATUS MOVE DOWN MENU TUS SURROUND AUTO PC POWER PC/DVI-D MODE Select an image level among Graphic, Standard, Text and Memory by pressing the PICTURE button on the Remote Control Unit. Press the ed buttons to select "Screen adjustment" menu and then press the OK button. "Screen adjustment" menu will appear. Press the ed buttons to select "Vertical" "Horizontal" or "Move", and adjust image by pressing the 78 buttons. Vertical Horizontal Move 1 1 1 78 Select 78 Adjust Adjustment data is memorized in each wide image mode. Vertical Adjustment of height of the image. Horizontal Adjustment of horizontal expand proportion on both sides of the image. Move Adjustment of vertical position of the image. STATUS Return M E N U Exit NOTE : "Vertical", "Horizontal" and "Move" may not be adjusted depending on the screen size selected. "Vertical", "Horizontal" and "Move" can not be adjusted when the input signal is PC or DVI-D. VIDEO COMPONENT ON-OFF UP/DOWN PICTURE PC/DVI-D VOLUME OFF TIMER MUTE To directly move up/down the image vertically, press the MOVE UP / MOVE DOWN buttons. NOTE : Up and down picture function can work only when the input signal mode is "AV1", "AV2", "AV3", "Component1" or "Component2" and the image mode is "Natural wide", "Zoom" or "Zoom(Caption-IN)". WIDE PICTURE MOVE UP MOVE UP button MOVE DOWN button OK STATUS MOVE DOWN MENU TUS SURROUND AUTO PC POWER POWER Move +3 28 COMPUTER MODE SELECTING INPUT SOURCE REMOTE CONTROL OPERATION Select "PC" or "DVI-D" by pressing the PC/DVI-D button on the Remote Control Unit. PC DVI (PC) FRONT CONTROL OPERATION Select "PC" or "DVI-D" by pressing the INPUT button on the Front Control of the Plasma Monitor. (Refer to P21) SELECTING COMPUTER SYSTEM This Plasma Monitor automatically tunes to most different types of computers based on VGA, SVGA or XGA (refer to "COMPATIBLE COMPUTER SPECIFICATIONS" on page 32). When selecting PC for the input mode, this Plasma Monitor automatically detects the incoming signal and displays a proper image without any special setting. (Some computers need manual setting. ) If the Monitor may not be able to display a proper image, the following messages will be displayed. Out of scan range When the Plasma Monitor detects any signal out of the system formats provided in the Compatible Computer Specifications on page 32 of this manual, the message "Out of scan range" will be displayed for a few seconds. [. . . ] When the Plasma Monitor has cooled down, the fans stop running. Internal fan is in trouble, not working properly. " When the message above is displayed, the internal cooling fans have some trouble. This message is displayed for 10 seconds in every 10 minutes. If this message is displayed frequently, contact sales dealer where you purchased the Plasma Monitor or the service center. INTERNAL TEMPERATURE MONITOR When the temperature inside the Plasma Monitor is abnormally high, the Plasma Monitor will be turned off automatically after displaying the message below. [. . . ]