User manual SANYO PDP42H1A

[. . . ] If your Plasma Monitor seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the Plasma Monitor or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This Plasma Monitor should be set in the way indicated. Take appropriate space on the top, sides and rear of the Plasma Monitor cabinet for allowing air circulation and cooling the Plasma Monitor. If the Plasma Monitor is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. [. . . ] Natural Normal picture level preset on this Plasma Monitor. Cinema Picture level adjusted for the picture with fine tone. Memory User preset picture adjustment in the IMAGE ADJUST Menu (P26). Dynamic Natural Cinema Memory In Video / Component mode VIDEO COMPONENT ON-OFF PC/DVI-D VOLUME OFF TIMER MUTE WIDE PICTURE MOVE UP PICTURE button OK STATUS MOVE DOWN MENU SURROUND AUTO PC POWER PC/DVI-D MODE Select an image level among Graphic, Standard, Text and Memory by pressing the PICTURE button on the Remote Control Unit. Graphic Select this mode when watching graphic images. Standard Normal picture level preset on this Plasma Monitor. Text Select this mode when watching text images. Memory User preset picture adjustment in the IMAGE ADJUST Menu (P26). Graphic Standard Text Memory In PC / DVI-D mode 22 BASIC OPERATION OPERATING ON-SCREEN MENU You can control and adjust this Plasma Monitor through the On-Screen Menu. Refer to the following pages to operate each VIDEO COMPONENT ON-OFF adjustment on the On-Screen Menu. PC/DVI-D VOLUME BUTTONS FOR ON-SCREEN MENU OPERATION REMOTE CONTROL UNIT CURSOR ed button CURSOR 7 8 button STATUS button WIDE OFF TIMER MUTE OK button PICTURE MOVE UP OK STATUS MOVE DOWN MENU MENU button SURROUND AUTO PC POWER ON FRONT CONTROL OK button MENU button MENU OK INPUT ­ VOLUME + CURSOR 7 8 button CURSOR ed button FLOW OF ON-SCREEN MENU OPERATION 1 2 3 4 5 Press the MENU button on the Remote Control Unit or the Front Control and the On-Screen Menu will appear. Press the ed buttons to select the menu that you want to adjust, and then press the OK button. (Refer to P21) SELECTING COMPUTER SYSTEM This Plasma Monitor automatically tunes to most different types of computers based on VGA, SVGA or XGA (refer to "COMPATIBLE COMPUTER SPECIFICATIONS" on page 32). When selecting PC for the input mode, this Plasma Monitor automatically detects the incoming signal and displays a proper image without any special setting. (Some computers need manual setting. ) If the Monitor may not be able to display a proper image, the following messages will be displayed. Out of scan range When the Plasma Monitor detects any signal out of the system formats provided in the Compatible Computer Specifications on page 32 of this manual, the message "Out of scan range" will be displayed for a few seconds. There is no signal input from the computer. Make sure the connection of the computer and the Plasma Monitor. No signal 29 COMPUTER MODE PC ADJUSTMENT PC MODE ADJUSTMENT "PC mode adjustment" menu is provided to adjust "Clock", "Phase", "Position" and "Power save" to conform to your computer. These functions can be operated as follows: 1 2 3 4 Press the MENU button and the On-Screen Menu will appear. Press the ed buttons to select "PC mode adjustment" menu and then press the OK button. "PC mode adjustment" menu will appear. Press the ed buttons to select an item that you want to adjust, and then press the OK button. The selected item will appear. PC MODE ADJUSTMENT MENU Picture adjustment Sound adjustment Screen adjustment Picture setup Initial setup PC mode adjustment Screen saver Information 78 Adjust each value by pressing the 78 buttons. Select OK OK STATUS Return M E N U Exit Auto setup "Auto setup" function is provided to automatically adjust "Clock", "Phase" and "Position" to conform to your computer. "Auto setup" can be started by pressing the the 8 button, and the message "Now adjusting" will be displayed. [. . . ] Disconnect the Power cord and contact the sales dealer where you purchased the Plasma Monitor or the service center. To turn the Plasma Monitor back on for checking: 1) Disconnect the Power cord from the AC outlet and plug it again. If the Plasma Monitor cannot be turned on, disconnect the Power cord and contact the service center. This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U. L. [. . . ]