User manual SANYO PDP42H1ENV

[. . . ] Make sure you understand these warnings when reading this installation manual. WARNING CAUTION This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling. This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling. This symbol indicates an action that must not be done. This symbol indicates an action that should be done. WARNING This setting plate is only for use with specified Sanyo projector. Do not use for any other equipment or purpose. Never modify the setting plate. Do not hang from the setting plate or hang heavy objects on the setting plate. Be especially careful that children do not hang from it. [. . . ] Be especially careful that children do not hang from it. Do not install the setting plate in a place where it might be subjected to vibration or shock. Never loosen the screws, bolts or nuts after installation. Do not use adhesives to prevent the screws loosening and do not use oils or lubricants for moving parts. If such substances are applied to the projector's cabinet, the cabinet may crack and fall, causing serious injury to people or serious damage to the projector. 1 Safety Instructions The installation work should be performed by at least two qualified service personnel. If you need to loosen any screws during installation, be careful not to drop the setting plate. Tighten all screws firmly after adjustment. Inspect the setting plate on a regular basis to ensure there are no broken parts or loose screws. Install the setting plate to a vertical wall. Do not install to a leaning wall. Do not install the setting plate in greasy or smoky place to prevent breakdown or abrasion of the projector's components. Do not install the setting plate in steamy, smoky or highly humid places in order to prevent fire or electric shock. Do not use a setting plate with damaged parts. The projector or setting plate may fall and cause personal injury or property damage. CAUTION Do not install the setting plate in a location where the operating temperature for your projector model may be exceeded. Such an environment may damage the projector. ¡ Use M12 nuts, bolts and washers (26 mm outside diameter). Nuts and bolts smaller than M12 could cause the setting plate to fall. (The wall plate must be secured in at least four places. ) ¡ Sanyo takes no responsibility for any damages or injury caused by incorrect installation. WARNING 6. 77 (172) 5. 15 (135) 4 English 1 Determine the position of the wall plate using the template sheet. Installation Procedure Attach the setting plate to the wall plate 1 Hang the setting plate hook onto the wall plate slits. Wall plate Setting plate 2 Tighten the four M8 x 20 mm hexagon socket head cap bolts supplied with the setting plate. (Secure temporarily so that the adjustment mentioned on page 7 can be carried out. ) Bolts Bolts 3 Attach the left and right cover plates to the setting plate using the two M5 x 10 mm hexagon socket head cap bolts included. (Secure temporarily so that the adjustment mentioned on page 7 can be carried out. ) Bolts 5 Installation Procedure Securing the projector to the setting plate Screws Adjustment unit Projector 2 Remove the two bolts (for drop-prevention) from the setting plate. Loosen the four bolts located on the top of the adjustment unit and set the projector with the adjustment unit onto the setting plate. Setting plate Bolts Loosen bolts Projector with the adjustment unit 3 Tighten the four bolts which were loosened to secure the projector to the setting plate. Attach the two bolts (for drop-prevention) to the setting plate. Bolts 6 English 1 Attach the adjustment unit to the projector using the included 5 screws (M4 x 18). Installation Procedure Adjustment 1 Adjust the forward/backward slide (Adjustable range: 0 - 180 mm) ¡ Loosen the four bolts on the top of the setting plate using a hexagon wrench (3 mm) and adjust the slider of setting plate. After the adjustment, tighten the four bolts which were loosened. Bolts 0 - 7. 09 inches (0 - 180 mm) 2 Adjust the vertical slide (Adjustable range: +4° - ­2°) ¡ Remove the left and right cover plates. ¡ Loosen the four bolts q located inside the setting plate using a hexagon wrench (6 mm). ¡ Adjust the vertical slide with the two bolts w located inside the setting plate using a hexagon wrench (6 mm) (Adjust the left and right bolts so that their ends touch equally against the wall plate. ) ¡ Tighten the four bolts q which were loosened using the hexagon wrench (6 mm). [. . . ] ¡ Loosen the four bolts q located inside the setting plate using a hexagon wrench (6 mm). ¡ Adjust the vertical slide with the two bolts w located inside the setting plate using a hexagon wrench (6 mm) (Adjust the left and right bolts so that their ends touch equally against the wall plate. ) ¡ Tighten the four bolts q which were loosened using the hexagon wrench (6 mm). ¡ After adjustment, attach the left and right cover plates again. Bolts q 4° Bolts w 2° 3 Adjust the horizontal rotation (Adjustable range: +5° - ­5°) ¡ Loosen the two bolts q located on the top of the setting plate using a hexagon wrench (3 mm). ¡ Turn the adjustment knob w located on the left side of the setting plate to adjust the horizontal rotation. [. . . ]