User manual SANYO PH-DTA100

[. . . ] If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. [. . . ] Displays the use time (Corresponding value) of the lamp. Timer . . . . . . . . . . . . . . . . . . . . . . . . Displays the timer setting status. OFF No timer setting. PJ-NET ORGANIZER OWNER'S MANUAL [PH-DTA100 Series] 1 ENGLISH Chapter 4 Controlling the Projector Multi-control Controlling and setting the multi-projectors This function enables you to control the multiple projectors equipped with the network units that are connected to the network. Click Multi Control on the main menu to display the control page. Note: To control the multiple projectors, each projector must have the same Network PIN code. Example of multi control PJ1 PJ2 PJ3 PJ4 PC6 PC5 Select Input2 for PJ1 to PJ4. PC4 Multi-control Start/stop the multi control To start or stop controlling the multi-projectors, click Multi control setting menu and select ON or OFF. Multi control setting OFF . . . . . . . . Stops multi control function ON . . . . . . . . . . The multi control menu will appear when setting ON. These items of menu are linked to the main menu. Switches on and off the multi-control function The multi controllable menus are "Power & Status", "PC adjustment", "Control", "Setting", "E-mail setting", "Timer", "SNMP setting" and "Network Viewer". Click each menu and perform setting and adjustment. The word "MULTI CONTROL" appears on the each control page while the multi control is operating. This shows the multi control is operating now. PJ-NET ORGANIZER OWNER'S MANUAL [PH-DTA100 Series] ENGLISH Chapter 4 Controlling the Projector Register the projector To use the multi control function, register the IP address of the projector you intend to control. Click PJ registration sub menu tab and set the IP address, Memo and Multi control item, then click Set button. Items Description IPaddress . . . . . . . . . . . . . Enter IP address of the projector to control Memo . . . . . . . . . . . . . . . . . . . . . . Enter projector name or installed location etc. Multi control item Control . . . . . . . . . . . . . . Controlling the projector Control & Image. . . . Controlling and displaying images Image . . . . . . . . . . . . . . . . . Displaying the images Confirmation of registered projector To check the registered information, click Conf. & Change page in the light mode Following functions in the "Conf. & Change" page are not available in the light mode. - Changing the control mode. - Deleting the registered IP address - Indicating the each status - Indicating the each memo This indicates that the mode is "VisualControl". This indicates that the mode is "Control". Connectionstatus Blinking: Connected Gray: Disconnected (Conf. &Change page in the light mode) Controlling all together "Power & Status", "PC adjustment", "Control" and "Setting" can be controlled all together. Set "ON" the multi control setting and adjust controls of each menu. The setting value is applied to the registered projectors sequentially . This is effective only if the multi control item of the registered projector sets to either "Control&Image" or "Control". Setting all together "E-mail setting", "SNMP setting" and "Timer" can be set all together. Set "ON" the multi control setting and items of each menu. The setting value is applied to the registered projectors sequentially. This is effective only if the multi control item of the registered projector sets to either "Control&Image" or "Control". Multi-control Viewer auto setting all together "Viewer auto display" can be set all together. Set "ON" the multi control setting and select [3] Auto display setting from Viewer sub menu (selected by "Multi-control" "Network Viewer" menu). Set the display time periods and repeat times for the auto image display. When clicking Start button, the registered projectors start playing back the auto image display in sequential. For further information of the Auto display, see "Using the net- work viewer function". [. . . ] Each piece of equipment must be assigned a unique IP address. If the IP address is set [192. 168. x. x], the Subnet Mask should be set [255. 255. 255. 0] for example. Rule2 The start address [xxx. xxx. xxx. 0] and the last address [xxx. xxx. xxx. 255] of the IP address must not be assigned to any other equipment. Rule3 The IP address must correlate to a network number. [. . . ]