User manual SANYO PLC-XU350

[. . . ] If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the end of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. Safety Precaution WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. ­ This projector produces intense light from the projection lens. Do not stare directly into the lens as much as possible. [. . . ] Press the POINT LEFT/RIGHT buttons to move the red frame pointer to the PC ADJUST Menu icon. Press the POINT UP/DOWN buttons to move the red frame pointer to the desired item, and then press the SELECT button. Press the POINT LEFT/RIGHT buttons to adjust the value. Fine sync PC ADJUST MENU PC ADJUST Menu icon Move the red frame pointer to an item and press the SELECT button. Eliminate a flicker from the display. Press the POINT LEFT/RIGHT buttons to adjust the value. (From 0 to 31. ) Total dots Adjust the number of total dots in one horizontal period. Press the POINT LEFT/RIGHT buttons to adjust the number to match your PC image. Selected Mode Shows status (Stored/Free) of the selected Mode. Position H Press the POINT LEFT/RIGHT buttons to adjust the horizontal picture position. Position V Press the POINT LEFT/RIGHT buttons to adjust the vertical picture position. Current mode Press the SELECT button to show H-sync freq. When the image has a dark bars, try this adjustment. Display area H Adjusts the horizontal area displayed by this projector. Press the POINT UP/DOWN buttons and move the red frame pointer to the desired function and then press the SELECT button. Normal SCREEN MENU SCREEN Menu icon Move the red frame pointer to a function and press the SELECT button. Provides the image to fit the screen size. True Provides image in its original size. Wide Provides the image to fit the wide video aspect ratio (16:9) by expanding the image width uniformly. This function can be used to provide the squeezed video signal at 16:9. Digital zoom + When the Digital zoom + is selected, the On-Screen Menu disappears and "D. Press the SELECT button to expand the image size. Press the POINT UP/DOWN/LEFT/RIGHT buttons to pan the image. The Panning function can work only when the image is larger than the screen size. The projected image can be also expanded by pressing the D. ZOOM button on the remote control. Digital zoom ­ When the Digital zoom ­ is selected, the On-Screen Menu disappears and "D. [. . . ] Reset the Lamp replacement counter after replacing the lamp. 56 APPENDIX TECHNICAL SPECIFICATIONS Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Panel Resolution Number of Pixels Color System High Definition TV Signal Scanning Frequency Motorized Lens Shift Horizontal Resolution Projection Lamp Input 1 Jacks Input 2 Jacks Input 3 Jacks Other Jacks Built-in Speakers Feet Adjustment Voltage and Power Consumption Multi-media Projector 12. 6" x 6. 6" x 16. 8" (319 mm x 168 mm x 429. 5 mm) 17. 4 lbs (7. 9 kg) 1. 3" TFT Active Matrix type, 3 panels 1024 x 768 dots 2, 359, 296 (1024 x 768 x 3 panels) PAL, SECAM, NTSC, NTSC4. 43, PAL-M, and PAL-N 480i, 480p, 575i, 575p, 720p, 1035i, and 1080i H-sync. 48 ~ 100 Hz Up and Down 800 TV lines (HDTV) 300 watt type DVI Terminal (Digital) HDCP Compatible, HDB 15-pin Terminal (Analog) and Stereo Mini Type Jack (Audio) BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H/V, and V), Stereo Mini Type Jack (Audio) RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L) and DIN 4-pin (S-Video) DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remote Jack and PJ-Net Organizer Connector INT. 10%) 0° to 10. 5° AC 100 ~ 120 V (5. 7 A Max. Ampere), 50/60 Hz (The U. S. A and Canada) AC 200 ~ 240 V (2. 7 A Max. [. . . ]