User manual SANYO PLC220N

[. . . ] This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the end of this booklet. [. . . ] Press the Point Down button to move the red frame pointer to the Auto PC Adj. icon and then press the SELECT button twice. This Auto PC Adjust can also be executed by pressing the AUTO PC button on the remote control. Auto PC Adj. PC Adjust Menu PC Adjust Menu icon Automatically adjusts Fine sync, Total dots, Horizontal, and Vertical for the input signal from your computer. To store adjustment data Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by selecting Mode in the PC System Menu (p25). See "Store" on page 28. NOTE G The PC Adjust Menu cannot be operated when the input signal is digital, a signal compatible with HDCP, or a memory card is installed into Multi Card Imager. G The Auto PC Adjust cannot be operated when 480i, 575i, 480p, 575p, 720p, 1035i, or 1080i is selected in the PC System Menu. Move the red frame pointer to the Auto PC Adj. icon and press the SELECT button. 26 Computer Input Computer Adjustment (Manual) Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector. This projector has Manual PC Adjustment to enable you to precisely adjust several parameters to match those signal formats. The projector has 5 independent memory areas to memorize those parameters manually adjusted. It is displayed at 5 : 4 aspect ratio with this function off. Reset Resets all adjustment to their previous levels. To store adjustment data Store To store adjustment data, move the red frame pointer to the Store icon and then press the SELECT button. Move the red arrow pointer to any of Mode 1 to 5 in which you want to store and then press the SELECT button. Mode free To clear adjustment data previously set, move the red frame pointer to the Mode free icon and then press the SELECT button. Move the red arrow pointer to the Mode that you want to clear and then press the SELECT button. Quit Closes the PC Adjust Menu. This Mode has parameters being stored. Press the SELECT button at the Display area icon and the Display area dialog box appears. Display area Vacant Mode shows values of "Total dots, " "Horizontal, " "Vertical, " "Display area H, " and "Display area V. " To clear adjustment data closes this dialog box. NOTE G Auto PC Adjust, Display area, Display area (H/V), and Full screen cannot be selected when "480i", "575i", "480p", "575p", "720p", "1035i", or "1080i" is selected in the PC System Menu (p25). 28 Computer Input Image Level Selection Direct Operation Select an image level among Standard, Real, Image 1, Image 2, Image 3, and Image 4 by pressing the IMAGE button on the remote control. Standard Normal picture level preset on this projector. Real Picture level with improved halftone for graphics. [. . . ] Reset the Lamp replace counter after replacement of the lamp. See page 43 and 44. 47 Appendix Menu Tree Computer Input / Video Input Input Computer 1 RGB( Analog ) RGB( PC Digital ) RGB( AV HDCP ) Computer 2 RGB Component RGB( Scart ) Video Auto Video S-Video Go to System (1) N/A N/A Go to System (1) Go to System (2) N/A Go to System (3) Go to System (3) Go to System (3) N/A - - - not applicable Computer Input System (1) MODE 1 MODE 2 SVGA 1 ---- Image Select Systems displayed in the System Menu vary depending on an input signal. Standard Real Image 1 Image 2 Image 3 Image 4 Contrast Brightness Color Temp 0 - 63 0 - 63 High Mid Low XLow Image Adjust PC Adjust Auto PC Adj. Total dots Horizontal Vertical Current mode Clamp Display area 0 - 31 640 x 480 720 x 400 800 x 600 1024 x 768 1152 x 864 1280 x 1024 1400 x 1050 Quit Red Green Blue Sharpness Gamma Reset Store Quit 0 - 63 0 - 63 0 - 63 0 - 15 0 - 15 Yes / No Image 1 Image 2 Image 3 Image 4 Quit Display area - H Display area - V Full screen Reset Mode free Store On / Off Yes / No Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Quit Screen Normal True Wide Digital zoom + Digital zoom ­ Quit 48 Appendix Video Input System (2) Auto 1080i 1035i 720p 575p 480p 575i 480i Auto PAL SECAM NTSC NTSC 4. 43 PAL-M PAL-N Standard Cinema Image 1 Image 2 Image 3 Image 4 Contrast Brightness Color Tint Color Temp 0 - 63 0 - 63 0 - 63 0 - 63 High Mid Low XLow Setting Sound Volume Mute Quit Language 0 - 63 On / Off Setting System (3) English German French Italian Spanish Portuguese Dutch Swedish Russian Chinese Korean Japanese Quit Store / Reset On / Off On / Off Image Select Keystone Blue back Display Logo Image Adjust Capture Ceiling Rear Terminal Standby mode Power management Off User Default Yes/No On / Off On / Off Computer 2 Monitor out Eco/Normal Off Ready Shut down 1-30 Min Quit Red Green Blue Sharpness Gamma Progressive Reset Store Quit 0 - 63 0 - 63 0 - 63 0 - 15 0 - 15 Off L1 L2 Yes / No Image 1 Image 2 Image 3 Image 4 Quit On start On / Off Pointer Remote control Screen Normal Wide Spotlight Pointer Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8 Quit Off Projector Remote Control Quit Yes / No Yes / No Key lock Lamp counter reset Factory default 49 Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 ­­­­­­­­ ­­­­­­­­ VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 VGA 7 MAC LC13 MAC 13 575i 480i SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 XGA 11 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 H-Freq. (kHz) 31. 47 31. 47 31. 47 37. 86 37. 86 37. 50 43. 269 34. 97 35. 00 15. 625 15. 734 35. 156 37. 88 46. 875 53. 674 48. 08 37. 90 34. 50 38. 00 38. 60 32. 70 38. 00 49. 72 48. 36 68. 677 60. 023 56. 476 60. 31 48. 50 44. 00 63. 48 36. 00 62. 04 61. 00 V-Freq. [. . . ]