User manual SANYO PLC510M

[. . . ] If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "TROUBLESHOOTING" section at the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. G This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. [. . . ] When computer is connected to Computer 1, select RGB. When video equipment is connected to Computer 1 terminal, select RGB (Scart). Refer to P31. Computer 1 INPUT Menu icon Move a pointer (red arrow) to Computer 1 and press SELECT button. RGB RGB (Scart) Source Select Menu Move a pointer to RGB and press SELECT button. When connect the output (Digital/Analog) from computer to Computer 2 (DVI-I) terminal on the projector. INPUT MENU 1 2 3 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon. Press POINT DOWN button to move a red arrow pointer to Computer 2 and then press SELECT button. Move a pointer to either RGB (Digital) or RGB (Analog) and then press SELECT button. When digital signal is connected to DVI terminal, select Digital. When analog signal is connected to DVI terminal, select Analog. Computer 2 INPUT Menu icon Move a pointer (red arrow) to Computer 2 and press SELECT button. RGB (Digital) RGB (Analog) Source Select Menu Move a pointer to RGB (Digital) or RGB (Analog) and press SELECT button. 22 COMPUTER INPUT SELECTING COMPUTER SYSTEM This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to "COMPATIBLE COMPUTER SPECIFICATIONS" on page 24). When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually. ) Note : Projector may display one of the following messages. Auto When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and the message "Auto" is displayed on SYSTEM Menu icon. (Refer to P25. ) When image is not provided properly, manual adjustment is required. icon and press SELECT button. Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by selecting Mode in PC SYSTEM Menu (P23). Refer to step 3 of MANUAL PC ADJUSTMENT section (P27). NOTE G Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment function. When the image is not provided properly through this function, manual adjustments are required. (Refer to page 26, 27. ) G Auto PC Adjustment function cannot be operated in Digital Signal input on DVI terminal and "RGB", "1035i (HDTV)", "1080i50 (HDTV)" or "1080i60 (HDTV)" is selected on PC SYSTEM Menu (P23). 25 COMPUTER INPUT MANUAL PC ADJUSTMENT This projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by MultiScan system of this projector. If this happens, projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. [. . . ] G LCD panels are manufactured to the highest possible standards. Even though 99. 99% of the pixels are effective, a tiny fraction of the pixels (0. 01% or less) may be ineffective by the characteristics of the LCD panels. 44 APPENDIX CONFIGURATIONS OF TERMINALS COMPUTER INPUT-1 and MONITOR OUT TERMINALS (ANALOG) Terminal : HDB15-PIN Pin Configuration 5 10 15 14 4 9 3 8 13 2 7 12 1 6 11 1 2 3 4 5 6 7 8 Red Input Green Input Blue Input Sense 2 Ground (Horiz. sync. ) Ground (Red) Ground (Green) Ground (Blue) 9 10 11 12 13 14 15 +5V Power Ground (Vert. sync. ) Sense 0 DDC Data Horiz. DDC Clock COMPUTER INPUT-2 TERMINAL (DIGITAL/ANALOG) Terminal : DVI-I 29-PIN Pin Configuration C1 C2 12345678 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C1 C2 C3 C4 C5 1 2 3 4 5 6 7 8 Analog Red Input Analog Green Input Analog Blue Input Analog Horiz. Data2/4 Shield +3. 3V MCI W-LAN DDC Clock DDC Data Analog Vert. [. . . ]