User manual SANYO PLCEF10NA

[. . . ] Multimedia Projector MODEL PLC-EF10NA MOD PLC-EF10NAL (Without Lens) Owner's Manual INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the owner's manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. TO THE OWNER As the owner of a new Multi-media Projector, you are probably eager to try out your new projector. [. . . ] Another dialog box IMAGE ADJUST DISPLAY will appear. This shows the current picture settings. In this dialog box, you can adjust the settings by increasing or decreasing the levels shown as numbers. The items and the range of the levels that you can adjust are summarized in the table below. Press the POINT DOWN BUTTON and a red arrow will appear. Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN BUTTON(s). To increase the level, point the arrow to v and then press the SELECT (REAR CLICK) BUTTON. To decrease the level, point the arrow to w and then press the SELECT (REAR CLICK) BUTTON. You may want to store the settings in the memory so that you can recall them later. To store the settings, move the arrow to Stored and then press the SELECT (REAR CLICK) BUTTON. When you have stored the settings, "OK ?" is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. The stored settings are memorized even if the MAIN ON/OFF is switched off. To quit the MENU, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. 10. If you do not want to store the settings, move the arrow to Quit and then press the SELECT (REAR CLICK) BUTTON. The settings changed remains effective until the MAIN ON/OFF switch is turned off. 11. To recall the settings from the memory that you have stored, move the arrow to Reset and then press the SELECT (REAR CLICK) BUTTON. When you have reset the settings, "OK ?" is displayed for confirmation. Move the arrow to Yes and then press the SELECT (REAR CLICK) BUTTON. You can adjust the settings again if needed. NOTE : "TINT" will be skipped in the PAL, SECAM, PAL-M and PAL-N mode. MAIN MENU DISPLAY IMAGE ADJUST DISPLAY TABLE OF PICTURE IMAGE ADJUSTMENT COLOR TINT WHITE BALANCE (R/G/B) CONTRAST BRIGHTNESS SHARPNESS DECREASES MORE PURPLE DECREASES LIGHTER DARKER SOFTER 0 0 0 0 0 0 63 INCREASES 63 MORE GREEN 63 INCREASES 63 DEEPER 63 BRIGHTER 31 SHARPER 38 VIDEO MODE PICTURE SCREEN ADJUSTMENT This projector has the Wide function, which enables you to view a wider video image. [. . . ] We will advise you how to obtain service. 56 APPENDIX TECHNICAL SPECIFICATIONS Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Number of Pixels Color System Scanning Frequency Projection Image Size (Diagonal) Horizontal Resolution Projection Lens Motorized Lens Shift Throw Distance Projection Lamp AV Input Jacks Video Monitor Output Jack Audio Monitor Output Jacks Computer Input 1 Jack Computer Input 2 Jack Computer Audio Input Jack Computer Output Jack Computer Audio Output Jack Other Jack Built-in Speaker Image Elevation Adjustment Voltage Power Consumption Operating Temperature Storage Temperature Remote Control Transmitters Multi-media Projector 15. 4" (390 mm) x 9. 6" (245 mm) x 23" (585 mm) 39. 2 Ibs (17. 8 kg) 1. 8" TFT Active Matrix type x 3 panels 3, 932, 160 {1, 310, 720 (1, 280 x 1, 024) x 3} 6 color system (PAL, SECAM, NTSC, NTSC4. 43, PAL-M and PAL-N) H-sync. 50 ~ 120 Hz Adjustable from 40" to 600" 800 TV lines F2. 0 ~ 2. 3 lens with f=75. 7 mm ~ 97. 5 mm Motor zoom and focus ± 760 mm on 100" screen 4. 9' (1. 5 m) ~ 80. 7' (24. 6 m) 440 watt type BNC Type {Video/Y, C/Cb (B-Y), Cr (R-Y)} x 2 sets, RCA Type (Audio R and L) x 2 sets and DIN 4 pin (S-Video) x 2 sets BNC Type {Video/Y, C/Cb (B-Y), Cr (R-Y)} x 1 set and DIN 4 pin (S-Video) x 1 set RCA Type (R and L) x 1 set MDR 20-pin Terminal (Digital), HDB 15-pin Terminal (Analog), Multi-pole 12-pin (Control port) and USB port BNC Type (R, G, B, H and V), Multi-pole 12-pin (Control port) and USB port RCA Type (R and L) x 2 sets HDB 15-pin Terminal RCA Type (R and L) x 1 set Wired Remote Jack and Serial port (DB 9) INT. Stereo (R and L), 3 watt RMS (T. H. D. 10%) Up to 4° 100 ~ 120 V AC, 50/60 Hz 7. 8 A (Max. Ampere) 5°C ~ 35°C ­10°C ~ 60°C Wireless Remote Control with Laser Beam (Class Laser) Max. [. . . ]