User manual SANYO PLCXU40

[. . . ] Multimedia Projector MODEL PLC-XU40 Owner's Manual TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. [. . . ] (kHz) 35. 522 46. 90 47. 00 58. 03 60. 24 68. 68 64. 20 62. 50 63. 90 63. 34 63. 74 71. 69 81. 13 63. 98 79. 976 60. 00 61. 20 71. 40 50. 00 50. 00 63. 37 76. 97 61. 85 46. 43 63. 79 63. 90 75. 00 80. 00 31. 47 31. 25 45. 00 33. 75 33. 75 28. 125 H-Freq. (Hz) 86. 96 (Interlace) 58. 20 58. 30 72. 00 75. 08 75. 06 70. 40 58. 60 60. 00 59. 98 60. 01 67. 19 76. 107 60. 02 75. 025 60. 00 65. 20 75. 60 86. 00 (Interlace) 94. 00 (Interlace) 60. 01 72. 00 66. 00 86. 70 (Interlace) 60. 18 60. 00 75. 08 75. 08 59. 88 50. 00 60. 00 60. 00 (Interlace) 60. 00 (Interlace) 50. 00 (Interlace) When an input signal is digital from DVI terminal, refer to the chart below. RESOLUTION 640 x 480 800 x 600 1024 x 768 RESOLUTION 1280 x 1024 1280 x 1024 1280 x 1024 D-VGA D-SVGA D-XGA D-SXGA 1 D-SXGA 2 D-SXGA 3 V-Freq. (Hz) 60. 02 58. 069 29. 80 NOTE : The projector may not project a proper image for D-SXGA 1, D-SXGA 2, and D-SXGA 3 depending on some computers. Specifications are subject to change without notice. 24 COMPUTER INPUT PC ADJUSTMENT AUTO PC ADJUSTMENT Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows. Auto PC Adj. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT button to move the red frame pointer to the PC ADJUST Menu icon. Press the POINT DOWN button to move the red frame pointer to the AUTO PC Adj. icon and then press the SELECT button twice. This Auto PC Adjustment can also be executed by pressing the AUTO PC ADJ. button on the Remote Control. PC ADJUST MENU PC ADJUST Menu icon Move the red frame pointer to the AUTO PC Adj. icon and press the SELECT button. Store adjustment parameters. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by selecting Mode in the PC SYSTEM Menu (P23). Refer to the step 3 of the MANUAL PC ADJUSTMENT section (P27). NOTE G The PC ADJUST Menu cannot be operated when the input signal is digital or RGB is selected in the PC SYSTEM Menu. G The Fine sync, Total dots, Horizontal, and Vertical of some computers cannot be fully adjusted with this Auto PC Adjustment function. When the image is not provided properly through this function, manual adjustments are required. (Refer to page 26, 27. ) G The Auto PC Adjustment function cannot be operated when "720p (HDTV), " "1035i (HDTV)", or "1080i (HDTV)" is selected in the PC SYSTEM Menu (P23). 25 COMPUTER INPUT MANUAL PC ADJUSTMENT This projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by MultiScan system of this projector. If this happens, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. [. . . ] When turning on the projector, the WARNING TEMP. It cannot be turned on until the READY indicator lights green. The projector detects an abnormal condition and cannot be turned on. Unplug the AC Power Cord and plug it again to turn on the projector. [. . . ]