User manual SANYO POA-PN03

[. . . ] index POA-PN03 LIN K ACT PJ-Net Organizer lus II Network Capture 3 Network Viewer 3 Network Communication OWNER'S MANUAL Compliance Federal Communication Commission Notice This equipment has been tested and found to comply SANYO POA-PN03 with the limits for a Class B digital device, pursuant to Tested To Comply part 15 of the FCC Rules. These limits are designed to With FCC Standards provide reasonable protection against harmful interference in a residential installation. This equipment generFOR HOME OR OFFICE USE ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] There are some disabled items in the multi-control function for the light mode. PJ-NET ORGANIZER OWNER'S MANUAL 65 ENGLISH Chapter 4 Controlling the Projector Conf. & Change page in the light mode Following functions in the "Conf. & Change" page are not available in the light mode. - Changing the control mode. - Deleting the registered IP address - Indicating the each status - Indicating the each memo This indicates that the mode is "VisualControl". This indicates that the mode is "Control". (Conf. &Change page in the light mode) Controlling all together "Power & Status", "PC adjustment", "Control" and "Setting" can be controlled all together. Set "ON" the multi control setting and adjust controls of each menu. The setting value is applied to the registered projectors sequentially . This is effective only if the multi control item of the registered projector sets to either "Both control" or "Control". Setting all together "E-mail setting", "SNMP setting" and "Timer" can be set all together. Set "ON" the multi control setting and items of each menu. The setting value is applied to the registered projectors sequentially. This is effective only if the multi control item of the registered projector sets to either "Both control" or "Control". 66 Multi-control Viewer auto setting all together "Viewer auto display" can be set all together. Set "ON" the multi control setting and select [3] Auto display from Viewer sub menu. Set the display time periods and repeat times for the auto image display. When clicking Start button, the registered projectors start playing back the auto image display in sequential. For further information of the Auto display, see "Using the net- work viewer function". (p. 98) This is effective only if the multi control item of the registered projector sets to either "Both control" or "Visual control". PJ-NET ORGANIZER OWNER'S MANUAL 67 ENGLISH Chapter 4 Controlling the Projector 68 Chapter 5 Network Capture Network Capture is a function to display the screen image of the computer via the network. - Real Time Capture - Network Communication 5 PJ-NET ORGANIZER OWNER'S MANUAL 69 ENGLISH Chapter 5 Network Capture About Network Capture function The Network Capture is a function to project the screen images of the computer which has a Network Capture 3 software by the projector through the network. This function has 2 kinds of mode as the below. - Real Time Capture (p. 72) A function to display the screen image of the computer by the projector through the network in real time. - Network Communication (p. 77) This mode is to communicate by sharing the capture image of a computer with multiple computers and a projector. User can draw the text and figure on the captured image by using a drawing tool. Up to 30 computers can be registered. The Network Capture function cannot be used when using the Network Viewer function. The Real Time Capture and Network Communication mode cannot be used at the same time. Launching the Network Capture 3 After installing the Network Capture 3 software, the shortcut icon is copied into the "Startup" folder. When you boot the computer, the Network Capture software also starts and its icon stays on the task bar. If the icon is not appeared on the task bar, the Network Capture 3 software is not starting. Click "Network Capture 3" from "Start" - "All the Programs" - "Network Viewer & Capture 3" menu to launch it manually. The status which the Network Capture 3 icon stays on the task bar is just preparing the screen capturing. Commands on the task bar When clicking the Network Viewer & Capture 3 icon on the task bar, The popup menu will appear as the right. [. . . ] Make sure that the input mode of the projector is "Network". Make sure that the Network Capture icon on the task bar of the computer is active ( p. 70). Make sure that the numbers of the capture port is the same as the projector's port number. If the alert message "Invalid Port No. " appears, your computer may be using this pot number already. [. . . ]