User manual SANYO POA-PN03C

[. . . ] index POA-PN03C D DC C O 8V U T 10 0m A VID EO IN LIN K ACT PJ-Net Organizer plus IIC NetworkCapture3 NetworkViewer3 NetworkCommunication OWNER'S MANUAL XP57 Series Compliance Federal Communication Commission Notice This equipment has been tested and found to comply SANYO POA-PN03C with the limits for a Class B digital device, pursuant to Tested To Comply part 15 of the FCC Rules. These limits are designed to With FCC Standards provide reasonable protection against harmful interference in a residential installation. This equipment generFOR HOME OR OFFICE USE ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The registered information of the projector is listed as the below. * The word "none" is displayed if not using the "Memo" function. * When you click on a listed IP address, the login page for the selected projector will be displayed with a new window. IP address Status Memo Page no. Click here to close the sub menu Conf. & Change. 10 projectors per page can be registered and up to 100 sets can be registered for the multicontrol. Multi-control Change the mode of the registered projector To change the mode of the registered projector, select a mode with the pull-down menu button under the IP address of the target projector and then click Set button. Mode Operation Control. . . . . . . . . . . . . . . . . . . . Controlling the projector Control & Image . . . . . . . . . Controlling and displaying images Image . . . . . . . . . . . . . . . . . . . . . . Displaying the images OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . Excluding from the multi-control Delete . . . . . . . . . . . . . . . . . . . . . . Deleting from the multi-control * The multi control item is not changed during using the network viewer function. It is not available with the light mode. Status If some of the registered projectors are disabled by some reasons (such as disconnecting the power source, disconnecting the LAN cable, disconnecting from the network), control changes will continue to be effective for the projectors that are still active. At the same time, the deactivated projectors are excluded from the multicontrol. The status of the registered projectors are indicated under the projector name. See the table below for status indications. Status Status Description (blank) . . . . . . . . . . . . . . . . . . . . . The projector is connected to the network correctly Noconnect . . . . . . . . . . The projector may not be connected to the network. Please check the connection and network configuration of this projector. The PIN code for the multi-controlled projectors must be the same. Change the PIN code of this projector to the common PIN code. Check if this projector is using the Network Capture function or Network Viewer function individually, or in the standby mode. * The network unit updates the status at the time when the multi-control function was executed. If the multi-controlled projector is in the standby mode, any change is not effective except timer setting. Cannot register, delete or change the multi-control setting during using the network viewer function. It is recommended that a specified projector should be chosen for setting as a master when you use this multi-control function. The control for the multi-controlled projectors will become too complicated operation if this function is used for each projector. If the registered projector is not connected to the network, it will take some time to complete the multi-control operation because of waiting for the response from each registered projector. There are some disabled items in the multi-control function for the light mode. PJ-NET ORGANIZER OWNER'S MANUAL [XP57 Series] ENGLISH Chapter 4 Controlling the Projector Conf. [. . . ] If network numbers are different between the equipment, they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q A What is the MAC address assigned to the network unit? The MAC address is indicated on the case back as the below. MAC Address MAC address PJ-NET ORGANIZER OWNER'S MANUAL [XP57 Series] 11 ENGLISH Chapter 7 Appendix Network capture Q A Why doesn't the computer screen appear on the projected screen? 1. Make sure that the input mode of the projector is "Network". Make sure that the Network Capture icon on the task bar of the computer is active (+ p. 70). [. . . ]