User manual SANYO VA-94S

[. . . ] 3 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control/Address Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Address Settings Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Improper connection may cause smoke or failures. Before attempting to connect each system component, carefully read the instruction manual that comes with it to familiarize yourself with the correct connection procedure. <Monitor Connection> <Power Connection> <Audio Jack Connection> <Network Connection> <Installing Recording Media> <Control Terminal Connections> Audio Jack Connection AUDIO OUT Jack (Black) Connect this jack via an audio cable to the audio input jack of an amplified speaker system or the monitor. AUDIO IN Jack (White) Use this jack to connect an external microphone to listen to the sound while monitoring the live video, or simultaneously record the video and sound. This terminal is compatible with a 3. 5-mm diameter mono microphone or line mono signals (only the left channel in cases of stereo signals). 6 Connections Network Connection This camera is designed so that you can use all of its functions via network operation. By connecting the network (LAN) socket of the camera to your PC using a LAN cable, you can configure and operate it from the Web browser installed on your PC. or LAN connection Switching hub Internet connection Internet Modem Router PC PC · Use a LAN cable no longer than 100 m (109. 4 yards) with the shield type CAT5 or higher. · Use a straight-type cable if connecting to LAN, and use a cross-type cable if directly connecting the camera to a PC. · The supported Web browser is Internet Explorer Ver. 6. 0 SP2 or higher, or Internet Explorer Ver. 7. 0. Installing Recording Media When recording live video on the camera, install an SD memory card or external hard disk on the camera. Always turn the power off when installing a recording medium. Connecting an External Hard Disk Put the hard disk in a dedicated hard disk case (VA-HDC4000; sold separately) and then connect the case to the camera. Inserting an SD Memory Card Insert the SD card into the slot until it is locked with a clicking sound. Push the SD card a bit further into the slot to eject it. · When you insert a new recording medium, format it on the SD/HDD screen. · When you remove the recording medium, first set [SD MEMORY CARD]/[HDD] on the SD/HDD screen to "NO USE". Control Terminal Connections Connect the alarm input/output cable and controller to the control terminal of the interface board. Use a thicker cable than 24AWG for connection. (Maximum length 600 m/656 yards) Installing and removing the interface board To place the board back, align the hole (A) at the right corner of the board to the protruding portion (B) and securely fix the board by depressing it. To connect alarm or other cables to the interface board, take out the board by pulling the portion (C). (C) (A) (B) 7 Connections COM OUT2 OUT1 C IN8 IN7 IN6 IN5 IN4 IN3 IN2 IN1 COM 485B 485A Alarm output signal OUT1/2 COM IN 1-8 Controller connection R D B K L L Alarm input signal O R B R B L WH S L L Y White Outputting Alarm Signals (OUT 1-2) Connect a buzzer, lamp, or other alarm device to the alarm output cable. Alarm can be output via two channels. · After connecting an alarm device, configure the output conditions for the corresponding alarm output terminal (ALARM OUT1 or 2) via network operation on the ALARM SETTINGS screen. · Configuration of alarm output terminal is also possible via remote operation. For that, set [ALARM OUT] to "REMOTE" on the ALARM SETTINGS screen. Inputting Alarm Signals (IN 1-8) Connect an alarm switch, infrared sensor, or other device to detect alarm conditions to the alarm input cable. Alarm can be input via eight channels. · After connecting an alarm device, configure the input conditions for the corresponding alarm input terminal (ALARM IN1 or 2) via network operation on the ALARM SETTINGS screen. · When using the alarm input terminal for day/night switching, configure the following settings. · Under [DAY/NIGHT], set [DAY/NIGHT] to "COLOR" and select the terminal you want to use in [EXT ALARM]. · On the ALARM SETTINGS screen, in [POLARITY], select the signal polarity of the alarm input G R Yellow terminal. · Connecting an external switch to ALARM IN1 allows you to set the system clock by operating the switch. To set the system clock, configure the [CLOCK IN] setting on the CLOCK SETTINGS screen. Connecting the Controller (485A/485B) By connecting a system controller (sold separately), the camera can be controlled remotely. Configure the protocol, baud rate and address. (Refer to "Control/Address Settings" Page 9. ) 8 Control/Address Settings When you connect the camera to a controller, it is necessary to configure the interface board control switch and address switch. Control switch This is used to configure transmission rate and protocol, etc. · Switches 4 and 5 are not used. · Settings in bold typeface in the table below show the factory default configurations. ON 1 2 3 4 5 6 Baud Rate Configure the transmission rate of connected devices to the transmission rate of the camera. ( Page 1) Connect the camera to the network to which your PC is also connected. Configue the network information on your PC. Configure information such as the IP address of your PC. Install the "H. 264 Plug-in" from the supplied CD-ROM onto your PC. You are now ready to monitor the surveillance video in the H. 264 format. [. . . ] · In the following situations, it is possible that recorded data may be lost (destroyed). Our company bears absolutely no responsibility for damages or profits loss due to the loss of data. · The medium (SD card or external hard disk) is not used correctly. · The medium is not installed on the device correctly. [. . . ]