User manual SANYO VCC-5984

[. . . ] INSTRUCTION MANUAL COLOR CCD CAMERA VCC-5984 About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. Depending on the conditions of use, installation and environment, please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. FEATURES · Built-in interline transfer method 1/3" CCD, approx. 410, 000 picture elements · Equipped with a DSP (Digital Signal Processor) function · Horizontal resolution, more than 520 TV lines · High sensitivity, minimum required illumination is 0. 3 lux (F1. 2, AGC gain HI position) · Two types of backlight compensation functions (multi-spot photometry and center focus photometry) · Low smear, anti-blooming, low lag, no burning and no geometric distortion using the CCD solid state image device. [. . . ] Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. When using lenses from other makers, the plug shape may not correspond to the terminal on the camera. In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug according to the diagram. (Refer to page 9. ) 3 2 CS mount type lens 3 8 English MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 1 Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. 2 Install the lens iris plug. 2 Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. Pin layout 2 4 1 3 2 4 1 3 1 2 3 4 DC type lenses Brake coil (­) Brake coil (+) Drive coil (+) Drive coil (­) VIDEO type lenses +12 V DC (50 mA max. ) Not used Video output (1. 0 Vp-p, high impedance) Ground (for video signal and DC power) Flange-back adjustment 2, 3 If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 3 ADJ. 1 LOCK 4 1 2 3 4 Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+). Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens. Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ. Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot. When the setting is complete, tighten the FLANGE BACK LOCK screw. English 9 CONNECTIONS 1 (A) AC 24 V connection Push to insert the cable 3 AC 24 V 2 (Video signal connections) : VIDEO IN : VIDEO OUT ~ ~ GND Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc. ), AC adaptor and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. Coaxial cable type and maximum length · Cable type RG-59U (3C-2V), 250 m maximum. · Cable type RG-6U (5C-2V), 500 m maximum. · Cable type RG-11U (7C-2V), 600 m maximum. CAUTION: · The RG-59U type cable should not be run through electrical conduits or through the air. · Using CCTV/Video-grade coaxial cable. 2 Use a commercially available 24 V AC adaptor. In such a case, add some lights to make sure the lighting is sufficient. If the lighting is very bright, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect. · Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the switch (1 ­ 3) to the up position. · The electronic iris is suitable for normal indoor use. When the switch (1 ­ 3) is set to the up position, do not use an auto-iris lens. · If used under fluorescent light, the image may flicker. In such a case, change to incandescent lighting or set the switch (1 ­ 3) to the down position and use an auto-iris lens. [. . . ] Is the flange-back position correctly set?If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens cleaning set. 16 English SPECIFICATIONS Camera: Scanning system Interlace Image device Picture elements Effective picture elements Synchronizing system : Internal sync, External sync, Automatically switchable Resolution : 520 TV lines horizontally, 350 TV lines vertically Video output level : 1. 0 Vp-p/75 ohms, composite Video S/N ratio : More than 48 dB Minimum required : Approx. 0. 3 lux with a F 1. 2 lens (GAIN, HI) illumination Approx. [. . . ]