User manual SANYO VCC-6594E

[. . . ] L53H4/US (VCC-6594) GB 2001, 11, 9 INSTRUCTION MANUAL COLOR CCD CAMERA VCC-6594 About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. L53H4/US (VCC-6594) GB 2001, 11, 9 SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by calling the toll-free number listed below. For product operation, authorized service center referral, service assistance or problem resolution, call CUSTOMER INFORMATION 1-800-421-5013 Weekdays 8:30 AM ­ 5:00 PM Pacific Time For accessories and/or parts, call PARTS ORDER INFORMATION 1-800-726-9662 Weekdays 8:30 AM ­ 5:00 PM Pacific Time THIS WARRANTY IS VALID ONLY ON SANYO PRODUCTS PURCHASED OR RENTED IN THE UNITED STATES OF AMERICA, EXCLUDING ALL U. S. THIS WARRANTY APPLIES ONLY TO THE ORIGINAL RETAIL PURCHASER OR END-USER. [. . . ] When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings. 1 2 32 CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. 1 1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw hole: 1/4"-20 UNC English 5 L53H4/US (VCC-6594) GB 2001, 11, 9 PARTS NAMES 9 Lens iris output connector (LENS) F 9 This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. F Camera setup section (under the cover) These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover. Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. When using lenses from other makers, the plug shape may not correspond to the terminal on the camera. In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug according to the diagram. (Refer to page 9. ) 3 2 CS mount type lens 3 8 English L53H4/US (VCC-6594) GB 2001, 11, 9 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 1 2 2 Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. Pin layout 2 4 1 3 2 4 1 3 1 2 3 4 DC type lenses Brake coil (­) Brake coil (+) Drive coil (+) Drive coil (­) VIDEO type lenses +12 V DC (50 mA max. ) Not used Video output (1. 0 Vp-p, high impedance) Ground (for video signal and DC power) Flange-back adjustment 2, 3 If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 3 ADJ. 1 LOCK 4 1 2 3 4 Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+). Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens. Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ. Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot. When the setting is complete, tighten the FLANGE BACK LOCK screw. English 9 L53H4/US (VCC-6594) GB 2001, 11, 9 CONNECTIONS 1 (A) 3 AC 24 V connection Push to insert the cable AC 24 V 2 (Video signal connections) : VIDEO IN : VIDEO OUT ~~ GND Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc. ), AC adaptor and cables are sold separately. Coaxial cable type and maximum length 1 2 3 Make the video signal connection between the camera and the monitor or time lapse VCR. Use a commercially available 24 V AC adaptor. Connect an AC 24 V power source to the AC 24 V input terminal on the back of the camera. Insert the plug of this power cord into a wall outlet. Adjust the picture on the monitor using the Brightness and Contrast controls etc. · Cable type RG-59U (3C-2V), 250 m maximum. · Cable type RG-6U (5C-2V), 500 m maximum. · Cable type RG-11U (7C-2V), 600 m maximum. CAUTION: · The RG-59U type cable should not be run through electrical conduits or through the air. · Using CCTV/Video-grade coaxial cable. 10 English L53H4/US (VCC-6594) GB 2001, 11, 9 SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. [. . . ] If a manual white balance adjustment is necessary, follow the steps below. Set the switch 8 (WB) to the up (M: manual) position, then adjust the colour. · Turn RED (VR302) to set the red ratio and/or BLUE (VR303) to set the blue ratio. Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below. VR301 R B VR302 VR303 8 L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast · If shooting simultaneously in a dark room and through a bright window. · If the subject background is extremely bright or dark. [. . . ]