User manual SANYO VCC-9684VA

[. . . ] If the camera requires service, never try to repair it yourself or open the casing. For servicing, maintenance, or repairs, consult your dealer or an Authorized Sanyo Service Center. INSTRUCTION MANUAL VCC-9684VA · Be careful when opening holes for installing the unit. Work with the power and video cables pulled out for easy installation. · Make sure to properly perform waterproofing for the ceiling or wall where you are installing the unit. Color CCD Camera About this manual Before installing and using the camera, please read this manual carefully. [. . . ] This installation should be made by a qualified service person and should conform to all local codes. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Sanyo may void the user's authority to operate this camera. Be careful when handling the unit To prevent damage, do not drop the unit or subject it to strong shock or vibration. Do not install this unit close to magnetic fields The magnetic fields may result in unstable operation. INSTALLING BASE PLATE AND CONNECTIONS Open the base plate. Protect from humidity and dust To prevent damage, do not install the unit where there is greasy smoke or steam, where the humidity may get too high, or where there is a lot of dust. Ceiling Installed 1 2 Push Monitor Connection Cable type RG-59U (3C-2V) RG-6U (5C-2V) RG-11U (7C-2V) Length 250 m (273 yds) max. 600 m (656 yds) max. 1 Protect from high temperatures Do not install close to stoves, or other heat sources, such as spotlights, etc. , or where it could be subject to direct sunlight, as this could cause deformation, discoloration or other damages. Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may rise to high levels. Point the arrow () in the same direction as the lens orientation. or more (A) · Diameter: 3. 5 to 5. 0 mm/0. 1 to 0. 2 in. · Height of screw head: 5 mm/0. 2 in. or less (washer included) · When using an RG-59U (3C-2V) cable, do not let it dangle in the air or attach it to piping. · If you use a cable other than the types above, the image or sync signal will be attenuated and will not be transmitted correctly. Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then dry by wiping with a soft cloth. · Do not use benzine, thinner or other chemical products on the cabinet, as this may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. [. . . ] If the vertical roll cannot be corrected by adjusting the LINE PHASE dial on the second and subsequent cameras, try adjusting the LINE PHASE dial on the first camera. If it still cannot be corrected, please check that the polarity of the power cords of all connected devices is correct. Only when using an auto-iris lens Multi-spot metering Backlight compensation to the entire screen* Center zone metering Backlight compensation to the central portion of the screen OFF High Normal 14 b Zoom and focus A Black screw Lens iris level adjustment If the entire image is too dark or too bright, adjust the condition. A. LENS 4 5 4 5 Low (darker) 4 5 LEVEL High (brighter) Push the camera unit until it clicks taking care not to pinch the cable. 2 Connect the cables from the wall. 3 Mount the camera unit to the base plate. A 1 Zoom Loosen the zoom ring knob A, and turn the zoom ring B to zoom in or out. Push the camera unit until it clicks taking care not to pinch the cable. B 4 5 * If the background of the object is extremely dark, set to Center zone metering. DC 2 Focus Loosen the focus ring knob C, and turn the focus ring D to focus on the object. 2 Supplied screw Supplied screw After finishing camera adjustments/settings . . . When finished, tighten the zoom and focus ring knobs AC securely. 1 Tighten the screw. 2 Install the dome cover. 1 Push the dome cover until it clicks. [. . . ]