User manual SANYO VDC-W1594VA

[. . . ] Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. [. . . ] Drill holes at the positions as marked and insert the supplied screw holds (H) in the holes. Cut a hole in the ceiling or the wall for routing the cables. Pass the power cable (I) and video cable (J) from the camera unit through the cable hole in the ceiling or the wall. Align the unit mounting holes of the camera unit with the holes in the ceiling or the wall. Secure with the supplied mounting screws (K). Carry out the settings and adjustments for the camera. Refer to "CONNECTIONS AND SETTINGS" for camera settings and lens adjustments. If a whole surface of the lens does not show through the camera window (L), loosen the screws (M) and adjust the dome liner (N). And then secure the dome cover by tightening the fixing screws (C) with the hexagonal wrench (large). (A) 46. 0 (B) (D) (K) (M) (L) (N) 8 9 10 11 Drop-prevention cord (C) 850 g (30 oz) Hexagonal wrench, Large, Medium and Small . . . . . . . each1 Rubber cushion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Mounting screw. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Screw hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Mounting template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 The factory setting value is represented in bold. Appearance and specifications are subject to change without prior notice. Since the conduit hole cover is not waterproof-finished, always be sure to seal the cover entirely by caulking, for example, upon completion of installation. Make sure to perform waterproofing properly to the ceiling or wall where you are installing the unit. When setting up this camera, make sure that it is installed securely. Check that the installation location is strong enough to bear the camera weight before proceeding. Install on a ceiling or wall that has no surface unevenness. In addition, do not touch the camera unit except when settings and adjustments are necessary. CONNECTIONS AND SETTINGS CONNECTIONS DC 12 V/AC 24 V connection Black Supported coaxial cables You can use any of the following coaxial cables: RG-59U (3C-2V) Length: 250 m (273. 4 yds) max. RG-6U (5C-2V) Length: 500 m (546. 8 yds) max. RG-11U (7C-2V) Length: 600 m (656. 2 yds) max. 2 Iris setting ON Down AI: Normal setting (Auto iris) EI: Electronic iris 5 Wide dynamic range setting (VDC-W1594VA) Correction is made for simultaneous monitoring of subjects which are different in brightness, one in a dark room and another in bright outdoor environment, for example. [. . . ] Loosen the zoom lever screw, turn the zoom lever to the right/ left to determine the zoom position while viewing the camera images on the monitor, and then re-tighten the screw. Loosen the focus lever screw, turn the focus lever to the right/ left to determine the focus position while viewing the camera images on the monitor, and then re-tighten the screw. Tighten the drop-prevention cord fixing screw. 1 Backlight compensation setting (VDC-C1574VA, VDC-D1584VA) ON Compensates for backlighting with the centerweighted metering mode. NOTE on image direction (Wall Installed): If the monitor image is misaligned, follow the steps below to adjust. Loosen the screws (B) with the supplied hexagon wrench (small). [. . . ]