User manual SANYO VPC-E890

[. . . ] INSTRUCTION MANUAL Digital Camera 8. 1 Mega Pixels VPC-E890 Preface i Preface About this Manual Copyright This manual contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. © Copyright 2009 Federal Communications Commission (FCC) Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] Power LED blinks during the charge and turns off automatically after the charge. The battery does not charge when room temperature exceeds 36 °C or falls below 6 °C. The battery does not charge again automatically even when the temperature comes back to 6 °C~36 °C, once the charge stops by higher or lower temperature. To recharge the battery, plug out the DC power supply cable or USB cable and plug in again by increasing or decreasing the temperature of the battery and the camera when room temperature is not suitable for charging. Turning On Press and hold the Power button to turn on the camera. To turn off the camera, press the Power button again. Charging the Battery Camera Setup 19 First Time Use Press the Power button as described in "Turning On" on page 18, a welcome screen displays momentarily on the LCD screen. If the camera is turned on for the first time, the Language menu pops up automatically after powering on the camera. Select the desired language by up/down navigation buttons, then press the OK button to confirm. LANGUAGE ENGLISH DEUTSCH FRANCAIS ITALIANO ESPANOL After the desired language is selected, the Date and Time menu pops up. Select each field and adjust the value using the navigation buttons. Press the OK button to confirm. DATE & TIME (Year) 2009 / 01 / 01 12 : 30 Press OK when done Note: If the Date and Time is reset (when running out the battery and not in use for a long period), the Date and Time setup screen displays automatically. First Time Use English 20 Getting Started Getting Started Now that you are familiar with the layout of your camera, you are ready to start taking photos and movies. Note: If the camera temperature exceeds 60 °C, a warning "HIGH CAMERA TEMPERATURE" will appear and the camera will shut down automatically to protect the safety of the camera and the user. English Taking your First Photo Taking a photo with the camera is very simple. Turn the camera on and press the SCENE button to access the Auto mode. Frame the shot on the LCD screen and press the Shutter button halfway. The camera automatically adjusts the focus and exposure. The focus bracket turns green when ready. Press fully and hold the Shutter button to capture the image. When a camera steady warning icon appears, hold the camera as still as possible, as a longer exposure time (more than 1/30 second) is required. Anti-Shake Function This function is available in Auto capture mode. Press the OK button to enable the Anti-Shake function, and press again to disable it. An Anti-Shake icon displays on the LCD screen when the function is activated. Taking your First Photo Getting Started 21 Using Macro Mode Macro mode is designed for close-up photography and can capture all detail even when your subject is very close to the camera. The Macro icon displays on the LCD screen. 35-70cm(Tele) Setting the Flash Mode You can choose from 4 flash modes to suit various lighting conditions. Press the Up/Flash /Delete navigation button to scroll through the four modes on the LCD screen. The flash setting remains the same for subsequent photos until you change it as described above. Auto flash: The flash fires automatically when needed. Anti Red-eye: The flash fires twice so as to reduce the red-eye effect. Using the Zoom in/out Function The camera comes equipped with 3x optical zoom and 5x digital zoom that allows you to zoom in on your subject. [. . . ] If the camera is not connected to a PTP compliant printer, an error message displays on the LCD screen. To enable PTP function, see "USB Mode" on page 45 for detailed information. If the USB mode is not set at PTP, an error message displays on the LCD screen. Connecting fail! When a PTP compliant printer is connected to the camera, the Printer Connecting screen displays on the LCD screen. The Print menu pops up automatically. Printer Connecting. . . Use the Up/Down navigation buttons to select an option and press the OK button to confirm. IMAGE STORAGE THIS IMAGE INDEX PRINT DPOF IMAGE ALL IMAGES 2/140 Image Storage See "Image Storage" on page 47 for detailed information. PictBridge Print (PTP) English 50 Camera Settings This Image Print the selected image with the current setting. Use the Up/Down navigation buttons to select THIS IMAGE from the options and press the OK button to confirm. Use the Left/ Right navigation buttons to select previous/next file. 2/140 IMAGE STORAGE THIS IMAGE INDEX PRINT DPOF IMAGE ALL IMAGES English 2. Press the Up/Down navigation buttons to set the number of copies. Number of copies 3 3. Press the Up/Down navigation buttons again to select the paper size. [. . . ]