User manual SCHOLTES SCH IF 632 CPD B

[. . . ] € Le présent appareil peut être utilisé par des enfants de plus de 8 ans et par des personnes présentant des capacités physiques, sensorielles ou mentales réduites ou n’ayant pas l’expérience ou les connaissances nécessaires, à condition qu’ils soient sous bonne surveillance ou qu’ils aient reçu les instructions nécessaires pour une utilisation de l’appareil en toute sécurité et à condition qu’ils se rendent compte des dangers encourus. 40 mm CÔTÉ AVANT DE LA TABLE DE CUISSON PLAN DE TRAVAIL 30 TABLE DE CUISSON RETOURNÉE 48 52 0 56 0+ /- 1 49 0+ /- 1 Aération Pour permettre une bonne aération et pour éviter toute surchauffe des surfaces autour de l’appareil, la table de cuisson doit être positionnée : • à au moins 40 mm de distance du mur arrière ou de toute autre surface verticale; • de manière à ce qu’il reste au moins 20 mm de distance entre la découpe d’encastrement et le meuble en dessous. , 27 Installation, 28-29 Positioning Electrical connection DE Deutsch, 39 ES Espanol, 52 Description of the appliance, 3 0 Control panel Start-up and use, 31 - 35 Switching on the hob Switching on the cooking zones Medium function Booster function Switching off the cooking zones Programming the cooking duration Timer Control panel lock Switching off the hob “Demo” mode EXTENSO TECHNOLOGY mode Practical advice on using the appliance Safety devices Practical cooking advice TIS TIS TIS TIS SCH 632 CDL S 62 CL S 632CPD L 62 CP L IF 632 CPD B Precautions and tips, 36 General safety Disposal Care and maintenance, 37 Switching the appliance off Cleaning the appliance Disassembling the hob Technical description of the models, 38 WARNING !€ WARNING: The appliance and its accessible parts become hot during use. [. . . ] Repeat the above procedure for each hotplate you wish to programme. Using multiple programmes and the display If one or more hotplates are programmed, the display will show the data for the hotplate with the least time remaining, and the light corresponding to the position of the hotplate will flash. The lights corresponding to the other hotplates programmed will be switched on. To visualise the time remaining for the other programmed hotplates, press the button repeatedly: the time remaining for each hotplate will be shown sequentially in a clockwise order, starting from the front left hotplate. Use the button repeatedly until the duration you buttons to set the new duration. Switching off the hob Press the button to switch off the appliance - do not rely solely on the pan sensor. If the control panel lock has been activated, the controls will continue to be locked even after the hob is switched on again. In order to switch the hob on again, you must first remove the lock function. €Demo” mode It is possible to set the hob to a demonstration mode where all the controls work normally but the heating elements do not switch on. To activate the “demo” mode the hob must be switched on, with all the hotplates switched off. At step 2, press the button: the duration decreases progressively until it reaches 0 and switches off. The programme resets and the display exits programming mode. When the 6 seconds have elapsed, the ON/OFF and CONTROLS LOCKED indicator lights will flash for one second. Release the and press the button; + and buttons • The display will show the text DE and MO and the hob will be switched off. € When the hob is switched on again it will be set to the “demo” mode. 32 To exit this mode, follow the procedure described above. The display will show the text DE and OF and the hob will be switched off. When it is next switched on, the hob will function normally. The EXTENSO TECHNOLOGY mode The EXTENSO TECHNOLOGY can be used to set the power of two "interconnected" hotplates to the same level. It can be activated if the two hotplates are OFF, by pressing the EXTENSO TECHNOLOGY button The EXTENSO TECHNOLOGY can be activated while the hob is on by pressing the EXTENSO TECHNOLOGY button once; the LEDs corresponding to both linked hotplates light up. The 2 LEDs remain lit as long as the hotplates are linked (if EXTENSO TECHNOLOGY button is pressed again, the hotplates are disconnected and are both set to power level 0). Pressing the +, - or Max buttons for one of the two Flexi hotplates also affects the display corresponding to the other hotplate. [. . . ] Loosen the screws fixing the alignment springs on each side. Loosen the screws holding the fixing hooks in each corner. Take the hob out of its installation cavity. Do not attempt to repair the appliance yourself. [. . . ]