User manual SCHOLTES SH09PGWAX

[. . . ] Operating Instructions HOB GB GB English, 1 Contents Installation, 2-7 Positioning Electrical connection Gas connection Data plate Burner and nozzle specifications Description of the appliance, 8 Overall view Start-up and use, 9-10 Practical advice on using the burners Precautions and tips, 11 SH09PGWAX General safety Disposal Maintenance and care, 12 Switching the appliance off Cleaning the appliance Gas tap maintenance Troubleshooting, 13 After sales support, 14 Installation !Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance. Please keep these operating instructions for future reference. [. . . ] Replacing the nozzles on separate double crown wok burners: 1. remove the grids and slide the burners from their housings. The burner consists of 2 separate parts (see figure); 5. Once the adjustment has been made, replace the seals on the by-passes using sealing wax or a similar substance. If the appliance is connected to liquid gas, the regulation screw must be fastened as tightly as possible. Once this procedure is finished, replace the old rating sticker with one indicating the new type of gas used. 0, 40 0, 40 0, 40 0, 40 75 55 -- 30 1, 65 1, 00 1, 50 0, 90 130 4, 10 1, 30 57 70 298 28-30 20 35 293 37 25 45 110 20 17 25 390 Nominal (mbar) Minimum (mbar) Maximum (mbar) 1013 mbar - dry gas P. C. S. The hob can only be installed above built-in ovens with a cooling ventilation system. C D C B A 7 Description of the appliance GB Overall view Gas burners Pan supports Control knobs Flame supervision device Ignition · Gas burners differ in size and power as described in the previous page. Use the diameter of the cookware to choose the most appropriate burner to cook with. · Control knobs allow to adjust the power or the size of the flame. · The ignition enables a specific burner to be lit automatically when a knob is pushed down ad turned. · The flame supervision device is a safety device that automatically shuts off the supply of gas to the affected burner if the flame is extinguished for any reason, preventing potential gas leaks. 8 Start-up and use !The position of the corresponding gas burner is shown on every knob. To turn on one of the burners press the relevant knob all the way down and turn it anti-clockwise to the full setting. To adjust the power of the burner and turn it off, follow the instructions previously described. GB Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: Off Maximum Minimum To light each of the burners, press down the corresponding knob and turn it anti-clockwise to the maximum setting. Since each burner is fitted with a flame supervision device, the knob should be pressed and held for approximately 2-3 seconds to allow the automatic device keeping the flame alight to heat up. When there is no electricity supply, the burners can be lit with a match after turning the control knob to the flame position. To turn on one of the burners, place a lighted match or lighter near the burner, press the knob all the way in and turn it anti-clockwise to the "High" setting. If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. To switch off the burner, turn the knob clockwise until it stops (when reaches the " " position). Double crown wok burner This burner consists of two concentric burners which can operate either together or separately. Use of the double crown wok burner on the maximum setting gives a very high power which reduces cooking times with respect to conventional burners. [. . . ] · Make sure that you have pressed the knob all the way in. · Make sure that you keep the knob pressed in long enough to activate the safety device. · Make sure that the gas holes are not blocked in the area corresponding to the safety device. · Make sure that there are no draughts near the appliance. [. . . ]