User manual SCHOLTES TG 644 P GH

[. . . ] Com 10 Operating Instructions HOB Contents Installation, 12-14 IT Italiano, 1 GB GB GB English, 11 FR Français, 20 Positioning Electrical connection Gas connection Burner and nozzle specifications BE Nederlands, 30 ES Español, 40 BE Deutsch, 50 Description of the appliance, 15 Overall view Start-up and use, 16 PT Português, 60 GR ÅëëçíéêÜ, 70 Practical advice on using the burners Data plate Precautions and tips, 17 General safety Disposal TG 644 P GH TG 755 P GH TG 755 P XX TV 644 P GH TV 755 P GH Maintenance and care, 18 Switching the appliance off Cleaning the appliance Gas tap maintenance Troubleshooting, 19 11 Installation !Before operating your new appliance please read this instruction booklet carefully. It contains important information for safe use, installation and care of the appliance. Please keep these operating instructions for future reference. [. . . ] Once connection has been carried out, make sure that the flexible metal pipe does not touch any moving parts and is not compressed. Only use pipes and seals that comply with current national regulations. Checking the tightness of the connection !When the installation process is complete, check the pipe fittings for leaks using a soapy solution. Should the gas pressure used be different (or vary slightly) from the recommended pressure, a suitable pressure regulator must be fitted to the inlet pipe (in order to comply with current national regulations). 78 MJ/m³ S R S R S S A A A TG 644 P GH TV 644 P GH TG 755 P GH TG 755 P XX TV 755 P GH 14 Description of the appliance Overall view GB Support Grid for COOKWARE GAS BURNERS Control Knobs for GAS BURNERS Support Grid for COOKWARE GAS BURNERS Control Knobs for GAS BURNERS Ignition for GAS BURNERS SAFETY DEVICES !The largest slot should be inserted into the ignition. Use the diameter of the cookware to choose the most appropriate burner to cook with. Control Knobs for GAS BURNERS adjust the size of the flame. SAFETY DEVICE stops the gas flow if the flame is accidentally extinguished. The rear grids stand a chance of being incorrectly positioned. In this case, the overlapping of the spokes will be clearly evident and the grid will not be aligned (see picture). The position of the corresponding gas burner or electric hotplate* is shown on every knob. Gas burners Each burner can be adjusted to one of the following settings using the corresponding control knob: · Off Maximum Minimum To turn on one of the burners, place a lighted match or lighter near the burner, press the knob all the way in and turn it anti-clockwise to the "High" setting. The knob must be pressed in for about 6 seconds until the device that keeps the flame lit warms up. Some models are equipped with an ignition button incorporated into the control knob. If this is the case, the ignitor is present. To light a burner, simply press the corresponding knob all the way in and then turn it anti-clockwise to the "High" setting, keeping it pressed in until the burner lights. If a flame is accidentally extinguished, turn off the control knob and wait for at least 1 minute before trying to relight it. To switch off the burner, turn the knob in a clockwise direction until it stops (when reaches the "· " position). Burner Fast (R) Semi Fast (S) Auxiliary (A) Ø Cookware Diameter (cm) 24 - 26 16 - 20 10 - 14 Practical advice on using the burners To ensure the burners operate efficiently: · Use appropriate cookware for each burner (see table) so that the flames do not extend beyond the bottom of the cookware. Always use cookware with a flat base and a cover. [. . . ] Special cleaning products for ceramic glass surfaces form a transparent protective layer which !Do not use stainless steel flame spreaders, bread toasters or meat grills over gas flames. Gas tap maintenance Over time, the taps may become jammed or difficult to turn. If this happens, the tap must be replaced. [. . . ]