User manual SEAGATE BARRACUDA 7200.10 SERIAL ATA

[. . . ] Product Manual Barracuda 7200. 10 Serial ATA ST3750640AS ST3750840AS ST3500630AS ST3500830AS ST3400620AS ST3400820AS ST3320620AS ST3320820AS ST3300620AS ST3300820AS ST3250620AS ST3250820AS ST3250410AS ST3250310AS ST3200820AS ST3160815AS ST3160215AS ST3120815AS ST3120215AS ST380815AS ST380215AS ST340815AS ST340215AS 100402371 Rev. J November 2007 evision history Revision Date Sheets affected or comments Rev. J 05/01/06 07/20/06 08/14/06 09/26/06 10/04/06 05/04/07 08/23/07 09/06/07 11/05/07 Initial release. 1, 3, 14-15, 26-28, 33, 35 and 49 10, 12, 14, 16, 19 and 27-28. [. . . ] 2. 8. 3 Voltage tolerance Voltage tolerance (including noise): 5V ± 5% 12V ± 10% Barracuda 7200. 10 Serial ATA Product Manual, Rev. J 31 2. 8. 4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Power modes Active Idle Standby Sleep Heads Tracking Tracking Parked Parked Spindle Rotating Rotating Stopped Stopped Buffer Enabled Enabled Enabled Disabled · Active mode The drive is in Active mode during the read/write and seek operations. · Idle mode The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc access is necessary. · Standby mode The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive accepts all commands and returns to Active mode any time disc access is necessary. · Sleep mode The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and enters Standby mode with all current translation parameters intact. · Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disc access is necessary. 32 Barracuda 7200. 10 Serial ATA Product Manual, Rev. J 2. 9 2. 9. 1 Environmental specifications Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions. Above 1, 000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10, 000 feet (3, 048 meters). Operating: Nonoperating: 0° to 60°C (32° to 140°F) ­40° to 70°C (­40° to 158°F) 2. 9. 2 Operating: Temperature gradient 20°C per hour (68°F per hour max), without condensation 30°C per hour (86°F per hour max) Nonoperating: 2. 9. 3 2. 9. 3. 1 Operating: Humidity Relative humidity 5% to 90% noncondensing (30% per hour max) 5% to 95% noncondensing (30% per hour max) Nonoperating: 2. 9. 3. 2 Operating: Wet bulb temperature 37. 7°C (99. 9°F max) 200 - 750 GB models: 37. 7°C (99. 9°F max) 40 - 160 GB models: 40°C (104°F max) Nonoperating: 2. 9. 4 Operating: Altitude ­60. 96 m to 3, 048 m (­200 ft. to 10, 000+ ft. ) ­60. 96 m to 12, 192 m (­200 ft. to 40, 000+ ft. ) Nonoperating: 2. 9. 5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. [. . . ] Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate. com Technical Support: DiscSupport@Seagate. com Warranty Support: http://www. seagate. com/support/service/index. html mySeagate my. seagate. com is the industry's first Web portal designed specifically for OEMs and distributors. It provides self-service access to critical applications, personalized content and the tools that allow our partners to manage their Seagate account functions. Submit pricing requests, orders and returns through a single, password-protected Web interface-anytime, anywhere in the world. [. . . ]