User manual SEAGATE CHEETAH NS 10K.2 SAS

[. . . ] Product Manual Cheetah NS 10K. 2 SAS ® ST3600002SS ST3450802SS 100516228 Rev. C November 2009 Copyright © 2009 Seagate Technology LLC. C, November 2009 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Cheetah, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. [. . . ] Shock is not to be repeated more than once every 2 seconds. Operating--abnormal Equipment, as installed for normal operation, does not incur physical damage while subjected to intermittent shock not exceeding 40 Gs at a duration of 11 ms (half sinewave). Shock occurring at abnormal levels may promote degraded operational performance during the abnormal shock period. Specified operational performance will continue when normal operating shock levels resume. Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more than once every 2 seconds. Non-operating The limits of non-operating shock shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives. The drive subjected to nonrepetitive shock not exceeding the three values below, shall not exhibit device damage or performance degradation. · 80 Gs at a duration of 11 ms (half sinewave) · 300 Gs at a duration of 2 ms (half sinewave) · 150 Gs at a duration of 0. 5 ms (half sinewave) Shock may be applied in the X, Y, or Z axis. Cheetah NS 10K. 2 SAS Product Manual, Rev. Packaged Disk drives shipped as loose load (not palletized) general freight will be packaged to withstand drops from heights as defined in the table below. For additional details refer to Seagate specifications 30190-001 (under 100 lbs/45 kg) or 30191-001 (over 100 lbs/45 Kg). Package size Packaged/product weight Drop height <600 cu in (<9, 800 cu cm) 600-1800 cu in (9, 800-19, 700 cu cm) >1800 cu in (>19, 700 cu cm) >600 cu in (>9, 800 cu cm) Any 0-20 lb (0 to 9. 1 kg) 0-20 lb (0 to 9. 1 kg) 20-40 lb (9. 1 to 18. 1 kg) 60 in (1524 mm) 48 in (1219 mm) 42 in (1067 mm) 36 in (914 mm) Drives packaged in single or multipacks with a gross weight of 20 pounds (8. 95 kg) or less by Seagate for general freight shipment shall withstand a drop test from 48 inches (1, 070 mm) against a concrete floor or equivalent. Z Y X Z X Y Figure 6. Recommended mounting 26 Cheetah NS 10K. 2 SAS Product Manual, Rev. Operating--normal The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding 10 - 300 Hz 301 - 500 Hz b. Operating--abnormal Equipment as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding: 15 minutes of duration at major resonant frequency Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational performance will continue when normal operating vibration levels are resumed. This assumes system recovery routines are available. Operating abnormal translational random flat profile 5 - 500 Hz 10-300 Hz c. Non-operating The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives. The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding 5 - 22 Hz 0. 25 G (0 to peak, linear, swept sine, 0. 5 octive/min) 22 - 350 Hz 350 - 500 Hz 3 G (0 to peak, linear, swept sine, 0. 5 octive/min) 1 G (0 to peak, linear, swept sine, 0. 5 octave/min) 0. 75 G (0 to peak) 0. 0029 G2/Hz 1. 0 G RMS (0 to peak) 0. 5 G RMS (0 to peak) Vibration may be applied in the X, Y, or Z axis. Vibration may be applied in the X, Y, or Z axis. 6. 4. 5 Acoustics Sound power during idle mode shall be 3. 4 bels typical when measured to ISO 7779 specification. Sound power while operating shall be 3. 6 bels typical when measured to ISO 7779 specification. [. . . ] For more information about the SCSI commands used by Seagate SAS drives, refer to the Seagate SCSI Commands Reference Manual, part number 100293068. 62 Cheetah NS 10K. 2 SAS Product Manual, Rev. C 10. 0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www. seagate. com. Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate. com Technical Support: DiscSupport@Seagate. com Warranty Support: http://www. seagate. com/www/en-us/support/warranty_&_returns_assistance mySeagate my. seagate. com is the industry's first Web portal designed specifically for OEMs and distributors. [. . . ]