User manual SEAGATE DB 35

[. . . ] DB35 Series ST3400832ACE ST3300831ACE ST3250823ACE ST3200826ACE DB35 Series ST3400832ACE ST3300831ACE ST3250823ACE ST3200826ACE ©2005, Seagate Technology LLC All rights reserved Publication number: 100347671, Rev. B May 2005 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, SeaTDD, and the Wave logo are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. [. . . ] · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Handle the drive by its edges or frame only. · The drive is extremely fragile--handle it with care. Do not press down on the drive top cover. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. DB35 Series Product Manual, Rev. B 15 3. 2 Breather filter hole precautions This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent possible damage to the drive. Breather hole Do not cover or seal this hole. Figure 3 Breather filter hole location Caution: Do not cover, seal, or insert any object into this hole. This hole has two purposes: · To allow condensation inside the hard disc to escape · To allow air pressure inside the hard disc to equalize with ambient pressure Note. If this hole is covered, sealed, or penetrated by any object, drive reliability may be compromised and could lead to permanent damage--doing so voids the warranty. 16 DB35 Series Product Manual, Rev. B 3. 3 3. 3. 1 Jumper settings Master/slave configuration The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8. Drive as master with a non-ATA-compatible slave. Use this jumper setting only if the drive does not work as a master with no jumpers installed. Options jumper block Master or single drive Drive is slave Master with non ATAcompatible slave Cable select Limit drive capacity to 32 Gbytes 7531 8642 Figure 4 Circuit Board Master/slave jumper settings 3. 3. 2 Cable-select option Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper on pins 5 and 6 as shown in Figure 4. [. . . ] If your location is not listed here, dial our European CSO warranty center at +31-20-316-7222 from 8:30 A. M. (Central Europe time) Monday through Friday. The CSO warranty center is located in Amsterdam, The Netherlands. Seagate Service Centers Toll-Free Support Numbers Call Center Austria Belgium Denmark France Germany Ireland Italy Netherlands Norway Poland Spain Sweden Switzerland Turkey United Kingdom Presales and Technical Support 0 800-20 12 90 00 800-47324283 (00 800-4SEAGATE) 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-311 12 38 00 800-47324283 00 800-47324283 00 800-47324283 00 800-31 92 91 40 00 800-47324283 Warranty Service 0 800-20 12 90 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-311 12 38 00 800-47324289 00 800-47324289 00 800-47324289 00 800-31 92 91 40 00 800-47324289 FAX Services--All Europe (toll call) Technical Support Warranty Service +1-405-324-3339 +31-20-653-3513 Africa/Middle East Support Services For presales and technical support in Africa and the Middle East, dial our presales and technical support call center at +1-405-324-4714 from 8:00 A. M. (Central Europe time) Monday through Friday. [. . . ]