User manual SEAGATE FIREBALL ICT10 JUMPER SETTINGS

[. . . ] Fireball lct10 fireball_lct10_jumper. pdf Jumper Settings DS Stand Alone (Default) Master with Slave Present Slave to Master Cable Select * ON ON OFF OFF CS OFF OFF OFF ON PK X X X X Rsvd OFF OFF OFF OFF X= PK is a Parking position. The presence or absence of this jumper has no effect on the drive. [. . . ] The Maxtor Fireball lct10 was developed by Quantum Corporation prior to its merger with Maxtor. BIOS Settings The following BIOS parameters are provided for customers needing to manually configure the Fireball lct10 disk drive. Both base 2 and base 10 capacity values are displayed. 5. 1 GB Logical Cylinders Logical Heads Logical Sectors/Track Total Logical Sectors Base 10 Capacity Base 2 Capacity 10, 585 15 63 10, 002, 825 5, 121 MB 4, 884 MB 10. 2 GB 16, 383 * 16 63 20, 044, 080 10, 262 MB 9, 787 MB 15. 0 GB 16, 383 * 16 63 29, 336, 832 15, 020 MB 14, 324 MB 20. 4 GB 16, 383 * 16 63 39, 876, 480 20, 416 MB 19, 470 MB 30. 0 GB 16, 383 * 16 63 58, 633, 344 30, 020 MB 28, 629 MB *Note: ATA (IDE) drives with a physical capacity greater than 8. 4GB have their default logical C/H/S values limited to 16, 383/16/63 as per the ATA-4 specification. Drives greater than 8. 4GB in capacity require LBA support. Capacity could be restricted to 8. 4GB (or less) due to system BIOS limitations. Check with your system or motherboard manufacturer to determine if your BIOS supports LBA mode for ATA hard drives greater than 8. 4GB. 2 of 2 Fireball lct10 fireball_lct10_jumper. pdf Special Considerations BIOS/Operating System Limitations Hard drives greater than 2. 1GB may need to be divided into multiple partitions / logical drives. MS-DOS versions 4. 0 through 6. 22 allow a maximum primary partition / logical drive size of 2. 1GB and are limited to 8. 4GB in physical drive capacity. The file systems supported by Windows 95, Windows 98 and Windows NT are not restricted to the 8. 4GB physical drive limit, but LBA support in the system BIOS is required. Hard drives greater than 8. 4GB in capacity may be restricted to 8. 4GB (or less) due to system BIOS limitations, operating system limitations, or both. Check with your system manufacturer to determine if your BIOS supports the correct LBA extensions for hard drives greater than 8. 4GB. Ultra ATA/66 Operation In order to achieve the Ultra ATA/66 transfer speed, you must have a system and a BIOS that will support Ultra ATA/66. The correct drivers must be loaded, and an Ultra ATA specific data cable must be used. The Ultra ATA cables use the Cable Select (CS) method rather than the Drive Select (DS) master/slave scheme, so the drive must be jumpered to enable Cable Select. [. . . ] Please observe proper mounting guidelines and specifications as described above when power is applied to the hard drive. For Further Review: · · · · · · · · · · ATA Configuration Card (Includes Drive Mounting) ATA Installation Flowchart ATA Installation Guide for Windows NT ATA Installation Guide for Windows95/98 BIOS Support for logical cylinder values > 4095 DOS/Windows 95 logical drive limitations Knowledge Base Windows NT 4. 0 Capacity Issue The Ultra ATA/66 bus interface Ultra ATA/66 Compatibility with Award BIOS 3 of 3 [. . . ]