User manual SEAGATE QUICKVIEW 300

[. . . ] Maxtor®Quickview 300 80/100/120/160/200/250/300GB PATA Product Manual May 24, 2005 Part Number: 000001922 May 24, 2005 Maxtor Corporation. This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein ­ which will be incorporated in revised editions of the publication. Maxtor may make changes or improvements in the product(s) described in this publication at any time and without notice. UL/CSA/VDE/TUV/WEEE/RoHS UL standard 1954 recognition granted under File No. [. . . ] 0 = Multiword DMA mode 1 is not selected 8: 1 = Multiword DMA mode 0 is selected. 0 = Multiword DMA mode 0 is not selected 7-3: 2: 1: 0: 64 15-8: 7-0: 65 Reserved 1 = Multiword DMA mode 2 and below are supported 1 = Multiword DMA mode 1 and below are supported 1 = Multiword DMA mode 0 is supported Reserved PIO modes supported Minimum Multiword DMA transfer cycle time per word 15-0: Cycle time in nanoseconds 66 Manufacturer's recommended Multiword DMA transfer cycle time 15-0: Cycle time in nanoseconds 5-8 Quickview 300 80/100/120/160/200/250/300GB PATA ATA Bus Interface and ATA Commands Table 5-2 Identify Drive Command Parameters Word 67 15-0: 68 CONTENT DESCRIPTION Minimum PIO transfer cycle time without flow control Cycle time in nanoseconds Minimum PIO transfer cycle time with IORDY flow control 15-0: Cycle time in nanoseconds 69-70 71-74 75 Reserved (for future command overlap and queuing) Reserved for IDENTIFY PACKET DEVICE command. Queue depth 15-5: 4-0: Reserved Maximum queue depth ­ 1 76-79 80 Reserved for Serial ATA Major version number 0000h or FFFFh = device does not report version 15: 14: 13: 12: 11: 10: 9: 8: 7: 6: 5: 4: 3: 2: 1: 0: Reserved Reserved for ATA/ATAPI-14 Reserved for ATA/ATAPI-13 Reserved for ATA/ATAPI-12 Reserved for ATA/ATAPI-11 Reserved for ATA/ATAPI-10 Reserved for ATA/ATAPI-9 Reserved for ATA/ATAPI-8 Reserved for ATA/ATAPI-7 1 = supports ATA/ATAPI-6 1 = supports ATA/ATAPI-5 1 = supports ATA/ATAPI-4 1 = supports ATA-3 Obsolete Obsolete Reserved Quickview 300 80/100/120/160/200/250/300GB PATA 5-9 ATA Bus Interface and ATA Commands Table 5-2 Identify Drive Command Parameters Word 81 Minor version number 0000h or FFFFh = device does not report version. 0001h-FFFEh = see 6. 16. 41 of ATA/ATAPI-7 specification 82 Command set supported. 15: 14: 13: 12: 11: 10: 9: 8: 7: 6: 5: 4: 3: 2: 1: 0: 83 Obsolete 1 = NOP command supported 1 = READ BUFFER command supported 1 = WRITE BUFFER command supported Obsolete 1 = Host Protected Area feature set supported 1 = DEVICE RESET command supported 1 = SERVICE interrupt supported 1 = release interrupt supported 1 = look-ahead supported 1 = write cache supported Shall be cleared to zero to indicate that the PACKET Command feature set is not supported 1 = mandatory Power Management feature set supported 1 = Removable Media feature set supported 1 = Security Mode feature set supported 1 = SMART feature set supported CONTENT DESCRIPTION Command sets supported. 15: 14: 13: 12: 11: 10: 9: 8: Shall be cleared to zero Shall be set to on 1 = FLUSH CACHE EXT command supported 1 = mandatory FLUSH CACHE command supported 1 = Device Configuration Overlay feature set supported 1 = 48-bit Address feature set supported 1 = Automatic Acoustic Management feature set supported 1 = SET MAX security extension supported 5-10 Quickview 300 80/100/120/160/200/250/300GB PATA ATA Bus Interface and ATA Commands Table 5-2 Identify Drive Command Parameters Word 83 7: 6: 5: 4: 3: 2: 1: 0: 84 CONTENT DESCRIPTION See Address Offset Reserved Area Boot, INCITS TR27:2001 1 = SET FEATURES subcommand required to spinup after power-up 1 = Power-Up In Standby feature set supported 1 = Removable Media Status Notification feature set supported 1 = Advanced Power Management feature set supported 1 = CFA feature set supported 1 = READ/WRITE DMA QUEUED supported 1 = DOWNLOAD MICROCODE command supported Command set/feature supported extension. 15: 14: 13-8: 7: 6: 5: 4: 3: 2: 1: 0: Shall be cleared to zero Shall be set to one Reserved 1 = WRITE DMA QUEUED FUA EXT command supported (ATA-7) 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands supported (ATA-7) 1 = General Purpose Logging feature set supported 1 = Streaming feature set supported (ATA-7) 1 = Media Card Pass Through Command feature set supported 1 = Media serial number supported 1 = SMART self-test supported 1 = SMART error logging supported 85 Command set/feature enabled. 15: 14: 13: 12: 11: 10: 9: 8: Obsolete 1 = NOP command enabled 1 = READ BUFFER command enabled 1 = WRITE BUFFER command enabled Obsolete 1 = Host Protected Area feature set enabled 1 = DEVICE RESET command enabled 1 = SERVICE interrupt enabled Quickview 300 80/100/120/160/200/250/300GB PATA 5-11 ATA Bus Interface and ATA Commands Table 5-2 Identify Drive Command Parameters Word 85 7: 6: 5: 4: 3: 2: 1: 0: 86 CONTENT DESCRIPTION 1 = release interrupt enabled 1 = look-ahead enabled 1 = write cache enabled Shall be cleared to zero to indicate that the PACKET Command feature set is not supported. 1 = Power Management feature set enabled 1 = Removable Media feature set enabled 1 = Security Mode feature set enabled 1 = SMART feature set enabled Command set/feature enabled. 15-14: 13: 12: 11: 10: 9: 8: 7: 6: 5: 4: 3: 2: 1: 0: Reserved 1 = FLUSH CACHE EXT command supported 1 = FLUSH CACHE command supported 1 = Device Configuration Overlay supported 1 = 48-bit Address features set supported 1 = Automatic Acoustic Management feature set enabled 1 = SET MAX security extension enabled by SET MAX SET PASSWORD See Address Offset Reserved Area Boot, INCITS TR27:2001 1 = SET FEATURES subcommand required to spin-up after power-up 1 = Power-Up In Standby feature set enabled 1 = Removable Media Status Notification feature set enabled 1 = Advanced Power Management feature set enabled 1 = CFA feature set enabled 1 = READ/WRITE DMA QUEUED command supported 1 = DOWNLOAD MICROCODE command supported 87 Command set/feature default. 15: 14: 13-8: 7: Shall be cleared to zero Shall be set to one Reserved 1 = WRITE DMA QUEUED FUA EXT command supported 5-12 Quickview 300 80/100/120/160/200/250/300GB PATA ATA Bus Interface and ATA Commands Table 5-2 Identify Drive Command Parameters Word 87 6: 5: 4: 3: 2: 1: 0: 88 15: 14: 13: 12: 11: 10: 9: 8: 7: 6: 5: 4: 3: 2: 1: 0: 89 90 91 92 CONTENT DESCRIPTION 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands supported General Purpose Logging feature set supported 1 = Valid CONFIGURE STREAM command has been executed 1 = Media Card Pass Through Command feature set enabled 1 = Media serial number is valid 1 = SMART self-test supported 1 = SMART error logging supported Reserved 1 = Ultra DMA mode 6 is selected. 0 = Ultra DMA mode 6 is not selected 1 = Ultra DMA mode 5 is selected. 0 = Ultra DMA mode 5 is not selected 1 = Ultra DMA mode 4 is selected. 0 = Ultra DMA mode 4 is not selected 1 = Ultra DMA mode 3 is selected. 0 = Ultra DMA mode 3 is not selected 1 = Ultra DMA mode 2 is selected. 0 = Ultra DMA mode 2 is not selected 1 = Ultra DMA mode 1 is selected. 0 = Ultra DMA mode 1 is not selected 1 = Ultra DMA mode 0 is selected. 0 = Ultra DMA mode 0 is not selected Reserved 1 = Ultra DMA mode 6 and below are supported 1 = Ultra DMA mode 5 and below are supported 1 = Ultra DMA mode 4 and below are supported 1 = Ultra DMA mode 3 and below are supported 1 = Ultra DMA mode 2 and below are supported 1 = Ultra DMA mode 1 and below are supported 1 = Ultra DMA mode 0 is supported Time required for security erase unit completion Time required for Enhanced security erase completion Current advanced power management value Master Password Revision Code Quickview 300 80/100/120/160/200/250/300GB PATA 5-13 ATA Bus Interface and ATA Commands Table 5-2 Identify Drive Command Parameters Word 93 CONTENT DESCRIPTION Hardware reset result. The contents of bits (12:0) of this word shall change only during the execution of a hardware reset 15: 14: 13: 12-8: 12: 11: 10-9: Shall be cleared to zero. 0 = device detected CBLID- below ViL Device 1 hardware reset result. Device 0 shall clear these bits to zero. Device shall set these bits as follows: Reserved. [. . . ] Each sector is preceded by ID data known as a header, which cannot be overwritten. Quickview 300 80/100/120/160/200/250/300GB PATA G-7 Glossary SUBSTRATE ­ The material the disk platter is made of beneath the magnetic coating. Hard disks are generally made of aluminum or magnesium alloy (or glass, for optical disks) while the substrate of floppies is usually mylar. SURFACE ­ The top or bottom side of the platter which is coated with the magnetic material for recording data. On some drives one surface may be reserved for positioning information. U UNFORMATTED CAPACITY ­ The total number of bytes of data that could be fit onto a disk. [. . . ]