User manual SEAGATE SCSI

[. . . ] Note that Termination Power is not the s ame as on-board termination, which this drive does not s upport. S S - S tagger S pin Pins 13-14 For most configurations this option is not utilized. M ost current S CS I host adapters offer a S tart Unit command enable or disable, which supersedes the functionality of the S S jumper setting. W hen the Delay S pin (DS ) jumper is enabled on the drive, the S tart Unit command from the S CS I host adapter will send S tart Unit commands to all devices on the bus at pre-determined intervals. [. . . ] S CS I ID Pin numbers 1-8 are typically referred to in pairs as A0 (pins 1 and 2), A1 (3, 4), A2 (5, 6), A3 (7, 8). The jumper pairs will allow configuration of S CS I ID's 0 to 15. All S CS I devices must have an individual ID on the S CS I bus (there is no M aster/S lave setting). S CS I ID 7 is usually reserved for the S CS I host adapter. Fault LE D and B us y Out J um pers Typical installations do not require the use of the Fault LE D and B usy Out jumpers. The B usy Out signal is usually supplied through the PCI bus to the PC motherboard's B usy indicator LE D. If connecting the B usy Out jumper for a drive installed in an external case, please refer to the wiring documentation supplied by the manufacturer of the case. Connection of the Fault LE D is not recommended in internal or external installations. Pin 1 Pin 2 Pin 1 Pin 2 Configure the Drive J umpers If specific jumper options are needed for your system configuration, refer to the illustrations and definitions provided in this section. SCSI ID 0 SCSI ID 1 SCSI ID 2 SCSI ID 3 NOT USED FAULT LED GROUND GROUND BUSY LED GROUND TERM POWER SCSI ID 3 SCSI ID 2 SCSI ID 1 SCSI ID 0 BUSY LED -/+ WRT PROTECT STAGGER SPIN DELAY SPIN SCSI ID J umper Settings ID Bit O OFF ON OF F ON OFF ON OFF OFF ON OFF ON OFF ON OFF ON ID Bit 1 OFF OFF ON ON OFF OFF ON OFF OFF ON ON OFF OFF ON ON D Bit 2 FF FF FF FF N N N OFF OFF OFF OFF ON ON ON ON ID Bit OF OF OF OF OF OF OF ON ON ON ON ON ON ON ON +5 V Pin 11 Pin 12 SINGLE ENDED Pin 17 Pin 18 RESERVED FOR SCSI HOS T 4 Pin Power Connector 12 Pin Option Connector M axtor S CS I drives typically s hip from the factory with jumpers s et to S CS I ID 6, and termination power jumped. S CS I ID 7 is us ually res erved for the S CS I hos t adapter. A ttention: The R ear J umper Option Connector is an OE M s pecific connector. M os t ins tallations w ill never us e the jumper options on this connector. Alw ays configure the drive us ing the jumpers at the Front J um per Option Connector . 68 Pin SCSI Connector N ote: M axtor LVD S CS I drives do not s upport on-board termination. M axtor recommends the us e of Active LVD terminators and 68-pin tw is ted pair cabling. S C S I hos t adapter manufacturers us ually s upply proper cabling and termination with the purchas e of an LVD S C S I hos t adapter. 3 Drive Install Installing 5. 25-inch Mounting Brackets If the hard drive will be installed in a 5. 25inch device bay, attach mounting brackets (available separately) to the hard drive as shown in the figure below. Installing Drive Inside of Y our Computer System M ake s ure your com puter is pow ered dow n before ins talling the drive. The following illus trations are of typical computer s ys tems and hard drive mounting s tyles . Your computer may have a different mounting s tyle. Pleas e refer to your computer us er manual for more information. B e s ure to s ecure the drive to the device bay with all four s crews . The drive s hould be oriented with its printed circuit board facing down. Mounting Screws Mounting Screws Mounting Bracket Computer with available 3. 5-inch device bay Computer with available 5. 25-inch device bay 4 Cable Hook-up Cable Connections for SCSI Drive Pin 1 68-pin Connector Attach the SCSI and Power Cables If the M axtor S CS I drive is the only device attached to the S CS I adapter card, attach the drive at the end of the Ultra LV D/S E cable, farthes t from the S CS I adapter card. This connector has a beveled edge and will only fit one way. [. . . ] W indow s N T/2000: B oot your system from the installation floppy disks provided with the OS to partition and format the drive. If you do not have the original installation floppies, you can create them using your W indows installation CD. W indow s X P: B oot your system from the W indows XP installation CD to partition and format the drive. If your system is not capable of booting from a CD, you can download bootable W indows XP installation floppies from M icrosoft's website at www. microsoft. com M acintosh: M ost non-Apple branded hard drives can be formatted using the Drive Setup utility included in M ac OS 8. 6 and above. [. . . ]