User manual SEARS C950-52474-5

[. . . ] The power cord should always be disconnected from the electrical outlet before the recovery tank is emptied, the solution tank is refilled or the cleaner is serviced in any way. DO NOT store this cleaner in an area which may reach freezing temperatures. Should this occur, DO NOT operate this cleaner until it has been at room temperature for at least (2) hours. DO NOT use any cleaning solution or chemicals other than those discussed in this manual. - STORE INDOORS. 8. [. . . ] Unwind Power Cord from power Head. See Figure 4. 3. lnsert plug on cord from Solution Tank into Receptacle in Recovery Tank power Head. Page 4 OPERATION See Figure 5. 4. Attach the large vacuum hose to recovery tank intake. Attach solution tubing to solution tank by inserting plastic insert into plastic coupling. NOTE: To remove plastic insert depress Tab and gently pull on plastic insert. Be careful not to pull on tubing as damage may occur. VACUUM CARPET See Figure 6. - PREPARATION - 1. the carpet be vacuumed to remove loose dirt before using the Cleaner. For best cleaning results it is recommended that PRETREAT CARPET (IF NEEDED) See Figure 7. 1' To remove stains and ground in soil present in heavy traffic areas of the carpet, spray or rub Sears Spotter (Formula #) into carpet before using the cleaner. Follow directions on the bottle. FILLING CLEANER WITH WATER AND CLEANING SOLUTION See Figure L 1. Add Sears Formula #1 carpet cleaning solution Follow directions on label of bottle. 2. Pour clean hot water in the Supply Tank - (f rom tap) into Filler Opening use 2 gallons of water. 3. Close Filler Opening. NOTE: This unit may become damaged water is used. if boiling Page 5 OPERATION ADD DEFOAMER (lF REOUIRED) See Figure 9. FOWER TIEAD 1. lf carpet has previously been cleaned. with regular it 'may be n-ecessary to add defoamer, tnlh-poo, '*e, to the recovery tank by raising Foimuta t-iiJtrei ani titting Power liead from the Re' -overy Tank. Follow directions on bottle' LATCH ftcunE 9 POWER HEAD POWER SWlTCtl CARPET CLEANING POWER CORD See Figure 10' POWEF COFD 1. Unwrap Power Cord from Power Head and plug into electrical outlet. 2. L Remove Recovery Tank from Solulion Tank. Note: lf foam is observed in Recovery Tank, add Sears Defoamer (Formula #2). Reassemble in the reverse of removal and resume cleaning. Figiure:15 DISASSEMBLY AND STORAGE See Figure 16' :f, There are three recommended methods of emptying the Solution Tank. a) Disconnect Pump Cord from Recovery Tank, remove recovery tank from Solution Tank and pour solution out of f iller opening. b) Place floor nozzle in bath tub or container. Depress solution release trigger and continue spraying until solution is no longer observed spraying through floor nozzle. c) Remove f loor nozzle and insert wand into solution tank through filler opening and vacuum solution out. Discard solution in recovery tank by follow- c F, igure 16 ing steps described under "How to Recovery Tank". Empty OPTIONAL CLEANING ACCESSORIES UPHOLSTERY NOZZLE Model No. 2081451 See Figure 17. Cleanmore Carpet Cleaner Upholstery Nozzle is an optional attachment for furniture upholstery clean' ing. The upholstery nozzle may also be used to clean cai upholstery or barpeting. ln addition, the nozzle may dlso be Jsed to clean carpeted stairs and other arehs difficult to clean with the normal floor nozzle. Page 8 Fig. 17 OPTIONAL CLEANING ACCESSORIES (Cont'd. ) HOME/AUTO CLEANING KIT Model 2081051 See Figure 18. Key No. Part Number Description Dust Brush Crevice Tool 1 2 3 4 642088-005 641671-013 642141-007 643737-005 Upholstery Nozzle (Dry) Upholstery Nozzle (Wet) SHOP VAC CLEAN. UP KIT Model No. 18 KeY No. Parl Number Description assembly contained in the below when "Dry" cleaning. 641871-007 6' Hose Assembly 641848-002 19-1/2" Wand (2) 641870-004 6" All-Purpose Nozzle 642620-002 14" Floor Nozzle 660424-001 14" Squeegee 660425-001 45' Dust Brush 642614-002 Crevice Tool NOTE: You must use the cloth filter 1 2 3 4 5 6 7 kit shown Fig. [. . . ] (2) Armatu re eomplete"wi fan Brush Assembiy (2) Brush Clamp (2i Screw, Brush Mtg. (2) lnsulator-Motor Cover Screw, Ground Screw, Brg. (2) Bearing Retainer Field Core Wound Self-Aligning Bearing - "O" Ring 82 83 84 85 86 Shaft-Pump Washer-Stainless Stl. Retaining Ring lmpel lerl Magnet/ Bearing Asm. [. . . ]