User manual SEAT COMMUNICATION SYSTEM

[. . . ] owner's manual COMMUNICATION SYSTEM auto emoción Owner's manual Communications system Foreword This owner's manual and the corresponding supplements should be read carefully to familiarise yourself with your vehicle. Also, the regular care and maintenance and correct handling of the vehicle will contribute to preserve its value. For safety reasons, note the information concerning accessories, modifications and parts exchange. If selling the vehicle, give all of the onboard documentation to the new owner as this should be kept with the vehicle. Contents 3 Contents Layout of the manual . . . . . . . . . . . . . . [. . . ] After this command you can listen to the names stored in the phone book After this command you can choose to delete the entire phone book or just a single name Effect After this command you can specify a telephone number and establish a connection After this command the last dialled telephone number will be redialled Effect Following this command the system announces possible orders Communication 11 Control commands The control commands are used to carry out functions that have already been chosen. The control commands are used during or at the end of a dialogue to carry out certain functions. Possible commands Speech command DIAL STORE CANCEL REPEAT Effect Telephone number already entered is dialled. A name is saved in the phonebook with its phone number Cancels a running dialogue. The specified name or all of the digits specified up to this point will be repeated. The system will then give the cue <Please proceed> so that you can specify additional digits or commands. The specified name or the last entered block of digits will be deleted. The system will then give the cue <Please proceed> so that you can specify additional digits or commands. The system will then give the cue <The number is deleted. After giving the command the last number dialled via the hands-free system will be dialled again. To record names in the phone book You can store names along with a telephone number in the internal telephone book. ­ Press the talk button . The beep tone indicates that the system is ready. ­ After the tone, say the command STORE NAME. After giving the command the system will request you to specify a name and telephone number to store in the internal telephone book. The telephone book has enough memory for 50 names and numbers. The telephone number can be specified all at once, in blocks of digits (separated by a brief pause), or as single digits. After each block of digits you specify (separated by a brief pause) the system will repeat the digits. The system can only recognise single digits (1, 0, 2, 5, etc. ), and not combinations of digits (e. g. Say STORE to store the entry into the telephone book. Speech command STORE NAME COMPANY XYZ Controls and equipment Condition Telephone book is not full System cue <The name, please?> <Please repeat the name> Effect Dialogue Dialogue 14 Communication COMPANY XYZ ZERO, ONE, TWO, THREE FOUR, FIVE, SIX <The number, please?> <Zero, one, two, three> <Four, five, six> Dialogue Dialogue Dialogue If no command is specified, the system responds after about 5 seconds with the next cue. No command <Possible commands: Store, repeat, back, delete, or specify additional digits> <The name is saved. > Dialogue STORE Dialogue - The name COMPANY XYZ with the telephone number 0123456 will be stored End of dialogue A running dialogue can be cancelled at any time with a press of the talk button . · · · · · · · Note If the telephone number has more than 20 digits, the system will decline and give the cue <The number is too long>. A Plus (+) can also be placed ahead of the 20 digits. Say the command Delete or Back to delete or correct the corresponding block of digits. Say Repeat to have all the digits that have been recognised up to that point repeated. If two or more names sound alike, it is better to save the names including the first name or some other distinguishing entry. A running dialogue can be cancelled at any time with a press of the talk button . [. . . ] Then, after turning on the ignition, select the option on the telephone to search for other Bluetooth communication devices within range, in other words, the hands-free system of the vehicle (SEAT_UHV). The next step is to select this hands-free system. The complete WARNING The Bluetooth function must be switched off during air travel (please refer to the phone manual). Communication 21 instructions for completing this operation should be found in the instruction manual for the telephone. The final step for establishing the connection is the introduction of the PIN code into the hands-free system (initially 1234). [. . . ]