User manual SEGA AQUARACE VER.0.2

[. . . ] 0. 2 For your safe and correct use, read this manual carefully and understand it thoroughly before operation. Please keep this manual in a safe place at all times and refer to it for any future references. Make sure to pass this manual on to future owners of Mini Rider2 when the product is moved or sold. BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLWING: To maintain safety: To ensure the safe operation of this product, be sure to read the following before usage. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. [. . . ] When multiple number of technicians are working at the same time, use extreme caution to prevent any possible collisions and accidents. Use caution while working with molded parts. This may cause injuries. 19 SIMULINE INC. . Installation is executed in the following order (1) Locating the product at the installation site (2) SENSOR installation (3) SIDE FENCE SUPPORTER installation (4) REAR SIDE FENCE installation (5) REAR FENCE installation (6) SIDE STEP installation (7) RIGHT FRONT FENCE installation (8) COINCHUTE TOWER installation (9) LEFT FRONT FENCE installation (10) BILLBOARD Installation (11) MSCU Installation (12) Power Cable 20 SIMULINE INC. . Tools needed for Installation Philips Screwdriver 24mm Spanner(M16) 10, 13, 17, 19, 24mm Ratchet(M6, M8, M10, M12, M16) 8mm(Ashai), 5/16(7. 95mm(HAPP)) Mini-Socket Wrench ­ Coin Frame Rachet Driver ­ MSCU Cable Cover 21 SIMULINE INC. . (1) Locating the product at the installation site Make sure that all of the adjusters are firmly lowered to the floor before starting the work. If not, the product can move out of place and cause accidens. This product is equipped with 4 casters and 4 adjusters. < Fig 7-1a> Move the product to the installation location. When installing next to a wall, make sure there is enough room for loading and unloading. Adjust the adjusters so the product is level. When the installation location is decided, lower the adjusters all the way to the floor. Lower the adjusters until the bottom of the caster is about 4mm from the floor. (Turing a full circle of spanner makes Adjuster go up by 2 mm. So, after fixing Adjuster, please revolve it with a spanner two times to two and half times. ) When satisfied with the adjustment, refer to Fig 7-1b and tighten the adjuster nut to fix the setting. < Fig 7-1b> 22 SIMULINE INC. . (2) SENSOR installation The installment position of SENSOR is as follows. Please install it conferring the following figure. < Fig 7-2a> It will be installed in SIDE FENCE SUPPORTER with four Hex Bolts (M6 x 20L). In installment, the SENSOR CABLE under the SENSOR must be in advance placed outside through the pipe. Please, be careful not to be confused with the direction of between the right and the left. The sensor attached with REFLECTOR should be in the left. < Fig 7-2b > 23 SIMULINE INC. . (3) SIDE FENCE SUPPORTER installation SIDE FENCE SUPPORTER can be installed at the side of BASE FRAME with four Hex Bolts (M6 x 20L). They must be installed at the both right and left sides of BASE FRAME. The upper side of REAR SIDE SUPPORTER and that of BASE FRAME should be fixed in a parallel way. Three SENSOR Cables must be connected and inserted inside. At this time, the cables must be connected with the ones with the same tags so that REAR and RIGHT SENSOR CABLE may not be exchanged. Please remember that when you step on REAR SIDE SUPPORTOR in the state of REAR SIDE FENCE not installed, it can be damaged. < Fig 7-3 > 24 SIMULINE INC. . (4) REAR SIDE FENCE installation REAR SIDE FENCE can be installed with eight Hex Bolts (M8 x 20L). < Fig 7-4a > It can be fixed by FIX NUT after lifting two Adjusters at the maximum level. Rear Side Fences must be installed at the both right and left sides of BASE FRAME. < Fig 7-4b > 25 SIMULINE INC. . (5) REAR FENCE installation REAR FENCE will be installed in the tap hall at the backside of REAR SIDE FENCE with eight Hex Bolts (M8 x 20L). In case the level of the hall is not fit in, please rearrange the height of ADJUSTER in REAR SIDE FENCE. < Fig 7-5 > (6) SIDE STEP installation SIDE STEP in the side of BASE FRAME can be fixed with four Hex Bolts (M8 x 20L). They must be installed at the both right and left sides of BASE FRAME < Fig 7-6 > 26 SIMULINE INC. . (7) RIGHT FRONT FENCE installation This can be installed at the right front of BASE FRAME with four Hex Bolts (M8 x 20L). < Fig 7-7 > (8) COINCHUTE TOWER installation After you open SIDE DOOR of COINCHUTE TOWER, you must place the cable through a wiring hole. < Fig 7-8a > 27 SIMULINE INC. . The CONNECTOR of the main body and that of COINCHUTE TOWER will be connected at the lower end of SIDE DOOR. The EARTH CABLE of the main body must be thrusted toward COINCHUTE TOWER, hooked on a BOLT, and fixed by a M4 NUT. < Fig 7-8b > COINCHUTE TOWER will be installed at the left side of BASE FRAME with four Hex Bolts (M8 x 20L). < Fig 7-8c > You can shut SIDE DOOR. 28 SIMULINE INC. . (9) LEFT FRONT FENCE installation This can be installed at the left front of BASE FRAME with eight Hex Bolts (M8 x 20L). < Fig 7-9 > 29 SIMULINE INC. . (10) BILLBOARD Installation After you push up the Billboard over the Monitor, you can hang it on CATCH CLIP, and fix it with four Hex Bolts (M8 x 20L) conferring the following figure. < Fig 7-10a > After opening the COVER at the backside of Billboard, you can connect LED POWER CABLE. And then you can close the COVER. < Fig 7-10b > 30 SIMULINE INC. . (11) MSCU Installation At first, MSCU CABLE COVER assembled at MUSC must be disjointed < Fig 7-11a > After you connect it with two VIBROISOLATION Bolts, M10 x 25L in the front side of BASE FRAME, you can push MUSC in a hole. < Fig 7-11b > The Connectors which are outside of the front of the main body and backside of MSCU should be connected according to their shapes. [. . . ] PBR-0460 PBR-0470 PBR-0480 PBR-0451 MET-03-025P PBR-0452 PBR-0453 ECB-05-024P WR06-020HNB W-FL06HNB W-SP06HNB TR04-008NNB FH-04NSN RW04-012NNB 73 SIMULINE INC. . 4. Ass'y Sensor(L) (PBR-0500) 201 2 3 4 101 201 2 202 2 203 3 2 Section A-A 203 4 102 2 5 A A 1 ITEM No. 1 2 3 4 5 101 102 201 202 203 DESCRIPTION SENSOR FRAME (L) SENSOR COVER - L SENSOR ADJUST BRAKET-L FOOT SENSOR FIX BRKT REFLECTOR SUPPORT PLATE PRK 25B[LEUZE] MECHATEM REFLECTOR [KEO SAMG] ROUND SEMS SCREW M3X8L ROUND SEMS SCREW M3X20L ROUND SEMS SCREW M4X8L PART No. PBR-0501 PBR-0502 PBR-0503 PBR-0504 PBR-0505 ESU-05-R046P ESU-05-R047P SR03-008NNB SR03-020NNB TR04-008NNB 74 SIMULINE INC. . 5. [. . . ]