User manual SEGA CASH CUBE

[. . . ] INTRODUCTION TO THIS SERVICE MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSTALLATION AND MAINTENANCE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HANDLING AND INSTALLATION PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NAME OF PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Ensure no incorrect coins or foreign objects are in the hopper. Ensure no badly bent coins in hopper. Clearing a coin jam 1. Open the Outer and Service doors to gain access to the Hopper area. . Detach the metalwork surrounding the hopper by removing the 2 screws and 3 nuts that hold it in place. Rotating the disc manually first anti-clockwise then clockwise to free the coin. Push the coin back in using the edge of similar coin. Do not return damaged coins to bowl. OR Remove any debris from the disc bed assembly. Clean the exit window opto with a clean dry cloth. Refill and test the hopper. Motor fails to run. Check 24v 5A fuse on the Hopper Drive Board. Hopper over-current protective device tripped (Wait 30 seconds while supply off). Over payout of coins 1. FUSES · Never touch places other than those specified. Touching places other than those specified can cause electric shock and short circuit. Disconnect the machine from the supply before attempting the replacement of any fuse. · · Only QUALIFIED SERVICE PERSONNEL should replace FUSES. Only replace fuses with ones of the same value and type. There are a number of fuses used on this machine to protect the user and the machine from damage. Only replace the fuse once you have removed the cause of its failure. Detailed below is a list of the fuses used, their location and if relevant PCB reference: PART NUMBER 514-5078-3150 514-5078-4000 514-5078-5000 514-5078-6300 LOCATION STEREO AMP REF. F1 TYPE & DETAILS 5x20mm CERAMIC SB 3. 15A 5x20mm CERAMIC SB 4A 5x20mm CERAMIC SB 5A 5x20mm CERAMIC SB 6. 3A QTY 2 1 1 1 There are also fuses located on the Monitor PCB. Refer to the monitor manufacturer for further information. 33 4. REFILL MODE 4. 1. WHAT IS REFILL MODE? The REFILL MODE is used to refill the Hopper with coins or to pay out coins from the Hopper. To enter REFILL MODE, hold the Key Switch in the "ON" position for around one second. Setting the Key Switch back to "OFF" will then exit REFILL MODE. [. . . ] [ 2] Success on try number 2, or failure on try number 3. [ 3] Success on try number 3, or failure on try number 4. [ 4] Success on try number 4, or failure on try number 5. [ 5] Success on try number 5, or failure on try number 6. [. . . ]