User manual SEGA CASH CUBE CLUB KART PRIZE

[. . . ] RND-0050 REV 1 SERVICE MANUAL CASH CUBE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. Manufactured in the UK by CONTENTS BEFORE USING THIS PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION 4 2. [. . . ] Check opto area/coin exit for dirt. Under Payout of coins 1. Ensure hopper contains sufficient coins. Poor connection (check common return wires) to hopper. 30 Dismantling the Hopper 1. Gently pull outwards the securing clips on the back of the base. Tilt the bowl forward until it is clear of the clips. Slide the bowl forward until the locating lugs, at the front of the bowl, are clear of the slots in the base. Lift the motor assembly out of the base. Disconnect the cable from the motor assembly. Hopper Assembly 1. Connect the cable to the motor assembly, ensuring that the 4-pin connector is the correct way round. Lower the motor assembly into the base, ensuring that the coin exit is in the rear exit position. Locate the lugs, on the front of the bowl, into the slots at the front of the base. Gently press down until the securing clips, on the base, click into the slots in the bowl. Routine cleaning: All accessible parts of the coin route should be cleaned periodically using a mild detergent on a damp cloth. Particular attention should be paid to the opto sensor at the coin exit to remove any build up of dirt. 31 3. 13. COIN MECHANISMS The machine uses a Coin Controls SR5 Coin Mechanism. 3. 13. 1. COIN MECHANISM OPERATION (FOR UK MACHINES). COINS ACCEPTED: 5P, 10P, 20P, 50P, £1, £2 COIN ROUTING The coin mech automatically routes all coins other than £1 coins to the cash box (exit C). £1 coins are routed to the hopper (exit A) until the float is achieved, afterwards they are diverted to the cash box (exit B). The float is maintained by software counting the number of £1 coins entered. The coin mech exits are as follows: A Hopper B Cash Box C Cash Box D Not Used. SR5 ­ COIN CONTROL ROUTING PLUG: 18 WAY Pt No PUB-64101UK 5-7, 8-15, 1à13, 10à13, 12à13, 16à13, 17à13, 18à13 The diode direction is shown as `à'. Note: Cash Payout - £1 Hopper only fitted. 3. 13. 2. COIN MECHANISM FAULT FINDING There is a green diagnostic LED used to provide a visual indication of the mechanisms current operation and error condition. LED ON = Power ON LED OFF = Power OFF LED will flash OFF once when Coins or Tokens are accepted or if reject Lever is pressed. LED will flash OFF twice if Coin or Token is unrecognised. LED will flash OFF three times if validator or machine has inhibited Coin or Token. LED will flash continuously when in Token Teaching Mode. For further information on the operation of the coin mechanism, please refer to the Money Controls website: www. moneycontrols. com/support/ 32 3. 14. [. . . ] [ 6] Success on try number 6, or failure on try number 7. [ 7] Success on try number 7, or failure on try number 8. [ 8] Success on try number 8, or failure on try number 9. [ 9] Success on try number 9, or failure on try number 10. [. . . ]