User manual SEGA DAYTONA SPECIAL

[. . . ] TEST 7-5 INPUT TEST 7-6 OUTPUT TEST 7-7 SOUND TEST 7-8 C. R. T. TEST 7-9 GAME ASSIGNMENTS 7-10 COIN ASSIGNMENTS 7-11 BOOKKEEPING 7-12 BACKUP DATA CLEAR 8. MAINTENANCE OF HANDLE AND SHIFT LEVER 8-1 ADJUSTMENT AND REPLACEMENT OF SWING VOLUME 8-2 GREASING 8-3 REMOVING SHIFT LEVER 8-4 SWITCH REPLACEMENT 9. ACCEL & BRAKE (S) 9-1 ADJUSTMENT AND REPLACEMENT OF VOLUME 9-2 GREASING 9-3 HAND BRAKE 10. [. . . ] In the case that the COIN CHUTE is changed, be sure the setting is made in a manner meeting the replaced coin chute. COMMON: Coins are accepted in common for both players. http://www. sauservice. com/manuals/Daytona2dlx_html/17day2dlx. html 7/12/2005 Coin Assignments Page 2 of 2 INDIVIDUAL: Each player uses a coin chute which accepts coins independently. CREDIT TO START: Number of credits required for starting game (1~5 credits are selected. ) CREDIT TO CONTINUE: Number of credits required for continuing game (1~5 credits are selected. ) COIN/CREDIT SETTING: Sets the CREDITS increase increment per coin insertion. There are 27 settings from #1 to #27, expressed in XX CREDIT as against XX COINS inserted. (TABLE 7. 10a, 7. 10b) #27 refers to FREE PLAY. When the COIN CHUTE TYPE is set to INDIVIDUAL, there are some setting numbers not displayed as indicated in TABLE 7. 10b. MANUAL SETTING: This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/CREDIT SETTING (refer to TABLE 7. 10c). http://www. sauservice. com/manuals/Daytona2dlx_html/17day2dlx. html 7/12/2005 Bookkeeping/Backup Data Clear Page 1 of 2 [Previous page][Next page][Table of Contents] 7 - 12 BOOKKEEPING Choosing BOOKKEEPING in the MENU mode displays the data of operating status up to the present are shown on 2 pages. Press the TEST BUTTON to proceed to PAGE 2/2. COIN CHUTE#*: Number of coins put in each Coin Chute. TOTAL COINS: Total number of activations of Coin Chutes. COIN CREDITS: Number of credits registered by inserting coins. SERVICE CREDITS: Credits registered by the SERVICE BUTTON. TOTAL CREDITS: Total number of credits (COIN CREDITS+SERVICE CREDITS). TOTAL TIME: The total energized time. http://www. sauservice. com/manuals/Daytona2dlx_html/21day2dlx. html 7/12/2005 Bookkeeping/Backup Data Clear Page 2 of 2 On page (2/2), each play frequency is displayed. When setting difficulty levels, the frequency can be referred to as a standard. When in the PAGE 2/2 mode, press the TEST BUTTON to return to the MENU mode. 7 - 13 BACKUP DATA CLEAR Clears the contents of BOOKKEEPING and high score player ranking entry. When clearing, bring the arrow to "YES" and when not clearing bring the arrow to "NO", by using the SERVICE BUTTON, and press the TEST BUTTON. When data has been cleared, "COMPLETED" will be displayed. Bring the arrow to "NO" and press the TEST BUTTON to cause the MENU MODE to return to the screen. Note that that contents of the GAME SETTING, COIN SETTING, and VOLUME SETTING are not affected by BACKUP DATA CLEAR operation. http://www. sauservice. com/manuals/Daytona2dlx_html/21day2dlx. html 7/12/2005 Mecha Unit/ Adjustment Page 1 of 5 [Previous page][Next page][Table of Contents] 8 . Do not touch places other than those specified. Touching places not specified can cause an electric shock or short circuit accident. If Accel. and brake operation is not satisfactory, adjustment of Volume installation position or Volume replacement is needed. Also, be sure to apply greasing to gear mesh portion once every 3 months. 9 - 1 ADJUSTMENT AND REPLACEMENT OF VOLUME This work should be performed by the Location's Maintenance man or Serviceman. Performing work by non-technical personnel can cause shock hazard. If appropriate value of each V. R. is as follows. Check volume values in the Test Mode. Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated portions. Touching places not specified can cause electric shock or short circuit accident. (1) Take out the 2 truss screws and remove the Front Cover fromthe Accel & Brake Unit. (2) Loosen the screw which secures the Potentiobase, and adjust the Volume value by moving the Base. http://www. sauservice. com/manuals/Daytona2dlx_html/23day2dlx. html 7/12/2005 Greasing to Gear portion Page 2 of 4 (3) Secure the Potentiobase. (4) Perform Volume setting in the Volume setting mode. In order to prevent an electric shock and short circuit accident, be sure to turn power off before performing work by touching the interior parts of the product. Damaged wiring can cause an electric shock or short circuit accident. Do not touch places other than those specified. Touching places not specified can cause an electric shock or short circuit accident. REPLACING THE VOLUME (1) Turn power off. (2) Disconnect the Connector. (3) Remove the Volume Bracket by taking out the 2 screws which secure the Volume Bracket. (4) Remove the Volume Gear and Volume Bracket to replace the Volume. Adjust gear mesh and ensure that Volume value display is within the range of 80+/-2H when the handle is in the centering position. http://www. sauservice. com/manuals/Daytona2dlx_html/23day2dlx. html 7/12/2005 Greasing to Gear portion Page 3 of 4 9 - 2 GREASING Be sure to use designated grease. [. . . ] PROBLEMS CAUSE COUNTERMEASURES Power is not supplied. Power Supply/Voltage is Make sure that power With Main SW ON, not correct. Remove the causes the power to cause of overload and be cut off due to replace fuse. 1. > Check to see if the POWER SW is ON. [. . . ]