User manual SEGA DINOSAUR KING

[. . . ] 420-6805-02 Nissay Aroma Building, 5-37-1, Kamata, Ohta-ku, Tokyo 144-8721, Japan Phone: +81-3-5480-6582 Facsimile: +81-3-5480-6584 © SEGA CORPORATION STOP IMPORTANT 1ST PRINTING MANUAL NO. 420-6805-02 TABLE OF CONTENTS BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS INTRODUCTION 1. HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PRECAUTIONS REGARDING INSTALLATION LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Test each Output equipment in the OUTPUT TEST or the CARD DISPENSER TEST mode. Check each Input/Output equipment in the Game Test mode. Adjust or replace each Input/Output equipment. If the problem still persists, check each equipment's mechanism movements. In the Monitor Adjustment mode, check to see if monitor adjustments are appropriate. 11-2 C, L 11-2, 11-3 A 11-4 (2), (6) 11-4 (3), (7) CONTROL SYSTEM 11-4 11-4 Sections 12, 13, 14, 16 Section 17 11-2 C, L MONITOR (CRT) IC BOARD - - 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 11-1 MAINTENANCE SWITCH UNIT AND COIN METER WARNING Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit accidents. STOP IMPORTANT Adjust the sound to an optimal level, taking into consideration the environmental requirements of the installation location. Removing the Coin Meter circuitry renders the game inoperable. Maintenance Switch Unit Open the service door, and the maintenance switch unit shown will appear. The function of each switch is as follows: (1) POWER SWITCH: (POWER) Switch ON/OFF the power supply. (2) DEMAGNETIZER BUTTON : Eliminates the on-screen color unevenness due to magnetization of CRT. Use this switch first before performing (DEMAG) the monitor's color adjustment. (3) TEST BUTTON: (TEST) (4) SERVICE BUTTON: (SERVICE) Press to enter Test Mode. Used during Test Mode to confirm or change selections. Gives credits without registering on the coin meter. Used during Test Mode to move the cursor. FIG. 11. 1a Coin Meter Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox. The Coin Meter counts the number of coins inserted into the coin slot. FIG. 11. 1b - - 11-2 COIN/CREDIT ASSIGNMENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Always set to COMMON. STOP IMPORTANT Any setting altered inside SYSTEM ASSIGNMENTS, COIN ASSIGNMENTS and GAME TEST MODE are saved only when ending Test Mode by selecting EXIT from the SYSTEM MENU. If the power is turned off before doing this, any alterations to settings will be lost. SYSTEM MENU SYSTEM INFORMATION RAM TEST I/O TEST SOUND TEST C. R. T. TEST SYSTEM ASSIGNMENTS ->COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING ROM TEST COMPACT FLASH TEST NETWORK SETTING GAME TEST MODE [****************************] EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON After turning on the power, press the TEST Button to bring up the SYSTEM MENU, as shown in the figure. Press the SERVICE Button to move the cursor. Move the cursor down to COIN ASSIGNMENTS and press the TEST Button. The COIN ASSIGNMENTS screen will appear. [. . . ] DKT-4401 421-12071 DKT-4402 440-CS0282-EG 560-5515-V-91 514-5138-4000 514-5144 514-5145 280-5207 000-P00416-W FAS-000159 068-441616 000-P00412-W DKT-60005 DESCRIPTION XFMR BASE STICKER FUSE RATINGS SG5013 T FUSE HOLDER BASE STICKER C FUSE REPLACEMENT ENG XFMR 100-120V 100V5A WB UL FUSE SG5013 5X20 4000MA 250V FUSE HOLDER 1P F-64-AD FUSE HOLDER COVER F-64-1C HARNESS LUG CC-1005 M SCR PH W/FS M4×16 M SCR PH W/SMALL FS M3×8 FLT WSHR 4. 4-16×1. 6 M SCR PH W/FS M4×12 WH FUSE HOLDER NOTE 16 17 18 19 20 21 22 23 24 - - 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 ASSY WH CABINET AC DKT-6001 This is comprised of the following wire harnesses. ASSY drawing is not available. ITEM NO. 601-0460 MKS-60001 DKT-60016 DKT-60010 DKT-60011 MKG-60033-01 DESCRIPTION PLASTIC TIE BELT 100MM WH WH WH WH WH AC EXT MONITOR & ELEC BASE EARTH ASSY ELEC BASE EARTH ASSY MAIN BD BASE EARTH DOOR EXT EXP NOTE ASSY WH CABINET DC DKT-6002 This is comprised of the following wire harnesses. ASSY drawing is not available. ITEM NO. [. . . ]