User manual SEGA F355 TWIN

[. . . ] Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary. Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. Be sure to understand the contents of the displays before reading the text. [. . . ] Feed the Roll Paper tip through the exit slot straight by hand until the paper tip can be seen from the exit slot. 10 Pull up the Head Up Lever. The Printer performs automatic feeding (AUTO LOADING) and cutting of the paper. 12 Put the ASSY Printer and lock the printer door to secure. www. seuservice. com 26 8. PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE When moving the machine, be sure to unplug the power plug. Moving the machine with the plug as is inserted can damage the power cord and cause fire and electric shock hazards. When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause electric shock and short circuit hazards. When lifting the cabinet, be sure to hold the grip portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions due to the empty weight of the cabinet, and cause personal injury. In the case the cabinet is separated into the front and rear portions, do not push the upper rear part of the front cabinet. Failure to observe this causes the front cabinet to fall down towards the monitor side and result in accidents and injury to persons. In cases the Steering operability is poor and the adjustment of VOLUME SETTING in the TEST mode is ineffective, the causes may be the Volume Gear's mesh failure and or Volume malfunctioning. By using the following procedure, adjust Volume gear mesh, or replace the Volume. In this product, when the Steering Wheel is moved fully left/right, if the Volume shaft is rotating within the movable range, the Volume is not feared to be damaged. Secure the Volume in the manner the Volume shaft is oriented as shown and the gears are appropriately engaged when the steering wheel is in the centering position allowing the car to go straight forward. REAR LID ADJUSTING THE VOLUME Be sure to use 2 workers in adjusting the Volume, one is for operating the Steering Wheel and the other one for performing the adjustment. 1 Turn off power. 2 Take out 4 Truss screws to remove the Rear Lid from the back of Front Cabinet. At this time, carefully support the Rear Lid as taking out the 4 Truss screws can cause the Rear Lid to drop. TRUSS SCREW (4) M4 X 16 PHOTO 9. 1 a www. seuservice. com 30 3 Perform the adjustment while another person is securing the Steering Wheel in the centering position. 4 The V. R. is on the VR BASE (a white, plastic made part). Loosen the 2 screws which secure the VR BASE and adjust the angle and appropriateness of gear mesh by moving the VR BASE. 5 Adjust to an appropriate mesh by securing the Steering Wheel in the direction allowing the car to advance straight forward and ensuring the "D" CUT FACE of the Volume shaft is oriented as shown. 6 Tighten the 2 screws to secure the VR BASE. VR BASE SCREW (2) M4 X 12, w/flat & spring washers "D" CUT FACE FIG. 8 Set the Center Value of the Volume in the TEST mode. 9 In the TEST mode, check to see if the Volume Value varies smoothly in accordance with the steering wheel operation. 31 www. seuservice. com REPLACING THE VOLUME SCREW (2) M4 X 12, w/flat & spring washers 1 Disconnect the connector from the Volume. 2 Take out 2 screws to remove the Volume together with VR BASE from the HANDLE MECHA. VR BASE PHOTO 9. [. . . ] 1 2 3 4 101 102 103 104 105 106 201 202 203 204 205 206 301 302 303 304 305 306 PART NO. FRI-4050 ~ APC-4001 105-5368 APC-4002 400-5397 280-5009-01 838-13760 280-0419 601-0460 270-5052-04 011-F00310 000-P00408-W 000-P00412-W 011-T03512 000-P00406-W 011-P00325 FRI-60017 FRI-60018 FRI-60019 FRI-60020 FRI-60021 FRI-60022 DESCRIPTION ASSY SHIELD CASE FRI ~ WOODEN MAIN BASE SHIELD CASE BRKT SW REGU BRKT SW REGU FOR JVS CORD CLAMP 21 DC SEQUENCE BD HARNESS LUG PLASTIC TIE BELT 100 MM L. FILTER D TAP SCR FH 3 X 10 M SCR PH W/FS M4 X 8 M SCR PH W/FS M4 X 12 TAP SCR TH 3. 5 X 12 M SCR PH W/FS M4 X 6 TAP SCR PH 3 X 25 WIRE HARN MAIN BD AC IN WIRE HARN MAIN BD DC OUT WIRE HARN MAIN BD DC A WIRE HARN MAIN BD DC B WIRE HARN MAIN BD DC C WIRE HARN MAIN BD DC D NOTE ( D-2/2 ) 135 www. seuservice. com 38 ASSY SHIELD CASE FRI ~ (FRI-4050 ~) ( D-1/2 ) www. seuservice. com 136 38 ASSY SHIELD CASE FRI ~ (FRI-4050 ~ ) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 101 102 103 201 202 203 204 301 302 PART NO. 105-5366 105-5367 839-1109-02 839-1110-02 833-13841 ~ 421-9174-01 421-10023-AAA 421-10023-BAM 441-313841 601-10577 105-5390 421-9757-L 421-9757-C 421-9757-R 260-0064 280-5275-SR10 601-0460 000-P00408-W 010-P00308-F 000-P00320-W 000-P00412-W APC-60045 APC-60046 DESCRIPTION SHIELD CASE NAOMI MULTI SHIELD CASE LID NAOMI MULTI FLT BD NAOMI MULTI MASTER FRI FLT BD NAOMI MULTI SLAVE FRI GAME BD FRI DX ~ STICKER CAUTION ANTISTATIC STICKER BD SERIAL NUMBER AAA STICKER BD SERIAL NUMBER BAM STICKER 833-13841 CARTON BOX NAOMI MULTI FIXING BRACKET STICKER L STICKER C STICKER R FAN MOTOR DC12V CORD CLAMP SR10 PLASTIC TIE BELT 100 MM M SCR PH W/FS M4 X 8 S-TITE SCR PH W/F M3 X 8 M SCR PH W/FS M3 X 20 M SCR PH W/FS M4 X 12 WIRE HARN FAN MOTOR MASTER WIRE HARN FAN MOTOR SLAVE NOTE ( D-2/2 ) 137 www. seuservice. com 39 ASSY PWR SPLY DX (FRI-4100) ( D-1/2 ) Note) 1. [. . . ]