User manual SEGA HOD2 UR

[. . . ] Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. Be sure to understand the contents of the displays before reading the text. DANGER Indicates that mishandling the product by disregarding this pictograph will cause severe injury or death. Indicates that mishandling the product by disregarding this caution will cause a slight hazardous situation which can CAUTION result in personal injury and/or material damage. Indicates that mishandling the product by disregarding this warning will cause a potentially hazardous situation which can WARNING result in death or serious injury. For the safe usage of the product, the following pictographs are used: Indicates "HANDLE WITH CARE. " In order to protect the human body and equipment, this display is attached to places where the Owner's Manual and/or Serviceman Manual should be referred to. In the case where warning labels are soiled or peel off, replace them immediately. [. . . ] If the game stop rectifying operation is not completed properly, thegamecannotberestored. · Adjust the sound to the optimum volume, taking into consideration the environmentalrequirementsoftheinstallationlocation. · Ifcoinmetercircuitryisremoved, thegamecannolongerbeplayed. TEST MODE -1 SWITCH UNIT The TEST Mode is performed by manipulating the ride switch unit. When the ride rotates, do the following for safety: sit in seat, fasten seatbelt and lower armrest. Unlock and open the ride control panel to find the switch unit. ENGLISH TEST MODE SOUND VOLUME SWITCH INITIALIZE BUTTON TEST BUTTON PHOTO 3-1 SERVICE BUTTON FIG. 3-1 SOUND VOLUME SWITCH (SOUND VOLUME): This is the sound volume adjustment knob. Sound volume increases as the knob is turned clockwise. In TEST Mode, this button is used to confirm or execute commands. SERVICE BUTTON (SERVICE): Makes it possible to enter credits when servicing the game without inserting coins for the coin meter. In TEST Mode, this button is used to select options. INITIALIZE BUTTON (INITIALIZE): Used for rectifying operation when the game has stopped. - SYSTEM TEST MODE ENGLISH TEST MODE · In SYSTEM TEST Mode, the settings reset by the user are recorded when the TEST Mode completes after EXIT from the SYSTEM TEST MENU. Periodically check the status of each input device on this screen. ENGLISH TEST MODE However, if the TEST Button is pressed and you move to TEST Mode before communication between the LINDBERGH and the control board is performed properly, there may be cases in which items are generated that cannot be confirmed on the INPUT TEST screen. In such cases, OFF, etc. , is displayed in gray. Reset the power supply. 1 On the GAME TEST MODE screen, select INPUT TEST and press the TEST Button. The INPUT TEST screen appears. INPUTTEST GUNTRIGGER GUNBUTTON GUNX GUNY SCREENIN SEATBELTSENSOR ARMRESTSENSOR ACTIONBUTTON GAMESTOP(RIDE) GAMESTOP(TOWER) MOTIONSELECTSW STARTBUTTON RESETBUTTON FOOTSENSORFRONT FOOTSENSORREAR FOOTSENSORLEFT FOOTSENSORRIGHT DOORSENSORLEFT DOORSENSORRIGHT INITIALIZE SERVICE TEST PLAYER1 OFF OFF 00 00 OUT LOCK DOWN OFF OFF OFF NORMAL OFF OFF OFF OFF OFF OFF CLOSE CLOSE OFF OFF OFF PLAYER2 OFF OFF 00 00 OUT LOCK PRESSTESTANDSERVICETOEXIT FIG. 3-3a INPUT TEST screen 0 GUN Y: Manipulate each switch, etc. , to check screen display. GUN TRIGGER: GUN BUTTON: GUN X: SCREEN IN: SEATBELT SENSOR: ARMREST SENSOR: ACTION BUTTON: GAME STOP (RIDE): GAME STOP (TOWER): MOTION SELECT SW: START BUTTON: RESET SWITCH: FOOT SENSOR REAR: FOOT SENSOR LEFT: FOOT SENSOR RIGHT: DOOR SENSOR LEFT: ON when the trigger of each player's Control Unit (Gun) is pulled. ON when each player's Control Unit (Gun) button is pressed. Displays the aim position of each player's Control Unit (Gun) in X direction. Displays the aim position of each player's Control Unit (Gun) in Y direction. IN when the aim of each player's Control Unit (Gun) is inside the screen. UNLOCK when the ride seatbelts are unfastened. ON when the ride ACTION Button is pressed. [. . . ] 5-2a RIDE 1 Confirm that all the adjusters contact the floor and that no objects have been placed in the spaces for evacuation and for smoke exhaust that were reserved when the product was installed. Confirm that the compressor drain tube is connected to the drainage container or drainage port. If there is a lot of drainage in the container, empty it. Confirm that all the breakers (switches) of the indoor power supply for this product are at ON. [. . . ]