User manual SEGA HOUSE OF THE DEAD 3 DX

[. . . ] 420-6742-01UK REV 0 SERVICE MANUAL DELUXE TYPE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. Manufactured in the UK by CONTENTS 1. BEFORE USING THIS PRODUCT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1. [. . . ] · All work to be carried out by QUALIFIED SERVICE PERSONNEL The GD-ROM Service Manual supplied with this product instructs you to remove the Key Chip when shipping the CHIHIRO Board. However, this product employs a dedicated CHIHIRO Board, therefore do not disassemble the CHIHIRO Board or remove the Key Chip. 3. 15. 1. REMOVING THE BOARD 1. Remove the two screws and unlock the LID UPPER. 3. Disconnect all harnesses connected to the CHIHIRO Main Board assembly as circled below. 34 4. Remove the two screws securing the base to the cabinet and withdraw the main board assembly upwards out of the cabinet. using the 2 hand holds in the board. 5. Pull the ASSY MAIN BD out of the Cabinet and set it on a level surface before continuing. Unplug all connectors connected to the Chihiro Board. Unplug the GD Cable connector on the side of the Media Board on the Chihiro Board. Unplug the AVIP Cable connected to the Chihiro Board. This is because the AVIP Cable is packed with it when the Chihiro Board is transported. Remove the 4 screws and remove the Chihiro Board from the Base. 35 3. 15. 2. REMOVING THE GD-ROM DRIVE Take out the ASSY MAIN BD from the PTV cabinet and remove the GD-ROM Drive from the ASSY MAIN BD as follows: i. Following the above procedure (steps 1 to 5), take out the ASSY MAIN BD. Remove the GD cable connector and the power cord connector from the GD-ROM Drive. 3. To remove the GD-ROM Drive, undo the four screws shown. 36 3. 16. COMPOSITION OF THE GAME BOARD 37 3. 17. PERIODIC CHECK AND INSPECTION The items listed below require periodic check and maintenance to retain the performance of the machine and ensure safe operation: · Be sure to check annually to see if the power cords are damaged. The plug is securely inserted and that there is no dust in the interior of the machine or between the socket and the power cord. Using the product in an unclean condition may cause a fire or electric shock. · Only QUALIFIED SERVICE PERSONNEL should carry out periodic checks. DESCRIPTION MONITOR / PROJECTOR GAME BD INTERIOR POWER SUPPLY CORD CABINET SURFACE CONTROL PANEL CONTROLLER (GUN) WHAT TO CHECK Clean screen Check adjustment Memory Test Game Assignments Clean (Do Not use water jet) Check condition Clean (Do Not use water jet) Lamp operation Check switch operation Clean Check sighting Check switch operation Weekly Monthly Monthly Monthly Annually Annually INTERVAL As required Monthly Monthly As required Weekly Monthly Monthly COIN MECHANISM Check SW (If Fitted) 38 4. HOW TO PLAY Use this section to confirm the machine is operating correctly; if the machine doesn't operate as described there may be a fault. While power is connected, the billboard is continuously lit and demonstration footage and ranking data are displayed on the screen. This `advertise' mode will be accompanied by sound from both speakers unless set otherwise in the TEST mode. The 1P and 2P start buttons have integral lights that flash when a credit is inserted. 39 4. 1. GAME CONTENTS 4. 1. 1. [. . . ] 1 2 3 4 5 6 7 8 9 10 101 102 103 104 105 201 202 203 204 301 PART NO. HDT-2120 HDT-2101 HDT-2102 HDT-2103 HDT-2104 HDT-2105 HDT-2106 HDT-2107 HDT-2108 JPT-2030 280-5124-02 280-5124-03 310-5029-D20 509-5080 601-0460 FAS-000092 FAS-000093 FAS-000094 FAS-120023 HDT-60007 DESCRIPTION NOTE ASSY SLIDE MECHA COVER L COVER R SLIDE GRIP L SLIDE GRIP R FRONT SIGHT TRIGGER TRIGGER SPRING STOPPER PIN SENSOR UNIT NYLON CLAMP NK02 NYLON CLAMP NK03 SUMITUBE F D 20MM SW MICRO TYPE (SS-5GL2) PLASTIC TIE BELT 100 MM M SCR PH W/SMALL FS BLK M3·~8 M SCR PH W/SMALL FS BLK M3·~16 M SCR BIND H W/TOOTH BLK M4·~8 TAP SCR P-TITE PH 3·~8 WH CONTROL UNIT 8. 13. JPT-2031 838-13144 012-P00306 DESCRIPTION NOTE SENSOR HOLDER SENSOR BD GUN SENSE TAP SCR #2 PH 3X6 96 8. 14. HDT-2180UK ASSY GUN HOLDER W/TETHER L Item 1 2 3 4 5 6 7 8 9 10 11 201 202 203 204 205 206 207 208 209 Component Part HDT-2181UK HDT-2182UK HDT-2183UK HDT-2184UK HDT-2185UK HDT-2186UK HDT-2187UK HDT-2188UK HDT-2197UK RTS-0306 HDT-2199UK 000-T00512-0B 008-P00620-0B 000-P00416-WB 008-T00416-0B 030-000616-0B 060-F00300 050-U00300 050-U00600 068-651616-0B Description GUN HOLSTER GUN HOLSTER SUPPORT GUN HOLSTER BRKT L PLATE HOLDER PLATE HOLDER BRKT L MDF HOLDER BASE L STICKER HOLSTER SIDE STICKER HOLSTER FRONT L GUN CUSHION MIC BOX U-BOLT GUN TETHER DX M5X12 MSCR TH BLK M6X20 TMP PRF TH BLK M4X16 MSCR PAN W/FS BLK M4X16 TMP PRF TH BLK M6X16 BLT BLK M3 WSHR FORM A FLT PAS M3 NUT NYLOK PAS M6 NUT NYLOK PAS M6 WSHR 16OD FLT BLK Qty. [. . . ]