User manual SEGA HOUSE OF THE DEAD 3 UPRIGHT

[. . . ] 420-6742-02UK REV 1 SERVICE MANUAL UPRIGHT TYPE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. Manufactured in the UK by CONTENTS 1. BEFORE USING THIS PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1. [. . . ] Reassemble in reverse order. 39 3. 15. COMPOSITION OF THE GAME BOARD 40 3. 16. TROUBLESHOOTING · Only QUALIFIED SERVICE PERSONNEL should carry out these procedures. If a problem occurs, first check the wiring connections. PROBLEMS CAUSE COUNTERMEASURES Firmly insert the plug into the outlet. When the main switch The power is not ON. is turned ON, the machine is not activated Incorrect power source/voltage. fuse) was activated due to an instantaneous overcurrent. Make sure that the power supply/voltage are correct. First, remove the cause of overcurrent and reinstate the circuit protection device to its original status. Then identify the cause of the fault on the item which caused the overcurrent & fix. The colour image on Incorrect monitor adjustment. the screen is incorrect The on-screen image of the monitor sways and/or shrinks Sound is not emitted The power source and voltage are not correct. Malfunctioning BD and Amp. Make appropriate adjustments. Make sure that the power supply and voltage are correct. Adjust the volume setting on the VTS bracket. SEE SECTION 6. 2 Perform Sound Test to check it. SEE SECTION 6. 3. 7 Check connector connection from Base to Speaker Adjust the gun sighting alignment. SEE SECTION 6. 4. 4 Replace the micro-switch. SEE SECTION 3. 11 Replace the fluorescent lamp. SEE SECTION 3. 13. 1 Check connector connections in the billboard case. Connector connection is incorrect Controller operation is Sighting is inaccurate due to not satisfactory environmental conditions, etc. Micro-switch malfunctioning Sensor BD is malfunctioning The fluorescent lamp does not light up The connector is disconnected Fluorescent lamp needs replacement 41 3. 17. FUSES · Never touch places other than those specified. Touching places other than those specified can cause electric shock and short circuit. Disconnect the machine from the supply before attempting the replacement of any fuse. · Only QUALIFIED SERVICE PERSONNEL should replace FUSES. · Only replace fuses with ones of the same value and type. [. . . ] 1 1 1 1 1 1 8 4 1 1 Description GUN HOLSTER GUN HOLSTER SUPPORT L GUN HOLSTER SUPPORT STICKER HOLSTER SIDE GUN CUSHION GUN TETHER UR M5X12 MSCR TH BLK M6X20 TMP PRF TH BLK M6 NUT NYLOK PAS M6 WSHR 16OD FLT BLK Component Reference (3)-8 (2)-4 (2)-1 (2)-1 103 9. 13. HDT-5170UK ASSY GUN HOLSTER R U/R Item 1 2 3 7 9 11 201 202 203 204 Component Part HDT-2181UK HDT-5152UK HDT-2182UK HDT-2187UK HDT-2197UK HDT-5153UK 000-T00512-0B 008-P00620-0B 050-U00600 068-651616-0B Qty. 1 1 1 1 1 1 8 4 1 1 Description GUN HOLSTER GUN HOLSTER SUPPORT R GUN HOLSTER SUPPORT STICKER HOLSTER SIDE GUN CUSHION GUN TETHER UR M5X12 MSCR TH BLK M6X20 TMP PRF TH BLK M6 NUT NYLOK PAS M6 WSHR 16OD FLT BLK Component Reference (3)-8 (2)-4 (2)-1 (2)-1 104 9. 14. HDT-6001UK ASSY WIRE L HDT U/R Item 101 102 301 302 303 304 305 306 Component Part 601-0460 280-N01610-0B 600-7009-2500 NOB-60045 NOB-60046 SPY-61043UK 600-7158-0100 HDT-61051UK Qty 12 0. 40 1 1 1 1 1 1 Description CABLE TIE 100mm SLIT HARN WRAP 16mm DIA 1M BLK ASSY RGB CA D-SUB 15P 2500MM WIRE HARN SPEAKER L WIRE HARN SPEAKER R WIRE HARN IC BD & DEMAG EXT CA AUDIO RCA TO RCA 2CH 100CM WIRE HARN DC SPLY & VOL CNTRL Component Reference 105 9. 15. [. . . ]